 Power for amp?, Best and easiest place to pull power from? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| drem914 |
 Apr 24 2019, 03:52 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,067 Joined: 16-May 08 From: Trabuco Canyon, CA Member No.: 9,062 Region Association: Southern California 
 |
I am looking to add an amp for a footwell subwoofer. Where is the easiest and best place to pull power from? I really don't want to run a power lead back to the battery. If I have to do that I probably will scrap the whole idea.
TIA |
   |
 
|
  |
Replies
| windforfun |
Apr 25 2019, 03:25 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,091 Joined: 17-December 07 From: Blackhawk, CA Member No.: 8,476 Region Association: None
|
Go with the largest power amp you can afford. Old cars aren't quiet - especially with the roof off & a loud exhaust system. Power it directly from the battery with a fuse & noise filter. Put the fuse at the battery & the filter at the amp. Trust me, BTDT. I prefer something along the lines of 100 W rms per channel. Don't waist your time with a little diddly shit power amplifier. If you blow out your loudspeakers, you'll know what to do next.
|
|
|
|
| Chris914n6 |
Apr 25 2019, 04:09 PM
Post
#3
|
|
Jackstands are my life. Group: Members Posts: 3,524 Joined: 14-March 03 From: Las Vegas, NV Member No.: 431 Region Association: Southwest Region |
140w RMS@4ohm should be fine for a 8" sub in our tiny car, but it depends if the rating of the speaker is close.
ex: a 280w speaker will be too tight to make much sound with 140w, but a 150w speaker would be in it's sweet spot. QUOTE(windforfun @ Apr 25 2019, 02:25 PM)  Go with the largest power amp you can afford. Old cars aren't quiet - especially with the roof off & a loud exhaust system. Power it directly from the battery with a fuse & noise filter. Put the fuse at the battery & the filter at the amp. Trust me, BTDT. I prefer something along the lines of 100 W rms per channel. Don't waist your time with a little diddly shit power amplifier. If you blow out your loudspeakers, you'll know what to do next. |
|
|
|
Posts in this topic
drem914 Power for amp? Apr 24 2019, 03:52 PM
jim_hoyland A separate line from the battery is recommended...... Apr 24 2019, 04:10 PM drem914 But I really don't want to drill anything or r... Apr 24 2019, 04:37 PM bandjoey fuse panel has 1/2 always hot and 1/2 switchable h... Apr 24 2019, 05:10 PM
drem914
fuse panel has 1/2 always hot and 1/2 switchable ... Apr 25 2019, 10:43 AM windforfun Don't forget the "Pi" filter. It at... Apr 24 2019, 05:20 PM Dave_Darling If your amp and sub are low-powered, you can proba... Apr 24 2019, 09:55 PM Steve I ran a thick wire through the center tunnel back ... Apr 25 2019, 06:28 AM drem914
I ran a thick wire through the center tunnel back... Apr 25 2019, 10:41 AM VegasVic
I ran a thick wire through the center tunnel back... Jun 1 2020, 06:05 PM Steve
I ran a thick wire through the center tunnel bac... Jun 1 2020, 07:38 PM VegasVic
Would you elaborate on your specific routing?
It... Jun 1 2020, 10:01 PM VaccaRabite Don't go through the fuse panel. Run a wire t... Apr 25 2019, 11:33 AM drem914
Don't go through the fuse panel. Run a wire ... Apr 25 2019, 03:07 PM porschetub Only way is direct to battery,nothing in the fuse ... Apr 25 2019, 03:03 PM drem914
140w RMS@4ohm should be fine for a 8" sub in... Apr 25 2019, 04:25 PM Chris914n6
currently have this 8" Polk DVC https://www.... Apr 26 2019, 04:08 PM windforfun
140w RMS@4ohm should be fine for a 8" sub in... Apr 25 2019, 05:49 PM bbrock I have a couple pics of routing my amp wire on my ... Jun 1 2020, 06:56 PM porschetub Did the same as Steve mentioned ,I used small posi... Jun 2 2020, 06:04 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 3rd March 2026 - 11:50 AM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.