 What are the trickiest parts about rebuilding one of these engines? Thanks |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Tdskip |
 May 1 2019, 08:43 PM
Post
#1
|
|
Advanced Member  Group: Members Posts: 3,737 Joined: 1-December 17 From: soCal Member No.: 21,666 Region Association: None 
 |
Or, in other words, where is a first time engine builder most likely to go wrong?
|
   |
 
|
  |
Replies
| Superhawk996 |
May 2 2019, 12:03 PM
Post
#2
|
|
914 Guru Group: Members Posts: 7,255 Joined: 25-August 18 From: Woods of N. Idaho Member No.: 22,428 Region Association: Galt's Gulch
|
@bbrock
To Brent's point, as long as the 11mm dimension 'C' doesn't go below 11mm you'll have room for the flywheel bolt heads. I just measured a bolt head and it is 9.2mm from shoulder to top of the head. |
 |
|
Posts in this topic
Tdskip What are the trickiest parts about rebuilding one of these engines? Thanks May 1 2019, 08:43 PM
Mark Henry Main bearing pinched on a dowel pin.
Trying to che... May 1 2019, 08:49 PM
Superhawk996
Thinking you know more about cooling tin, flaps,... May 2 2019, 05:50 AM Tdskip That’s a good starting list-thanks May 1 2019, 09:17 PM Mblizzard Incorrect alignment of cam and crank timing marks.... May 2 2019, 06:59 AM bbrock
Not surfacing pressure plate mounting surface the... May 2 2019, 07:35 AM Mblizzard
Not surfacing pressure plate mounting surface th... May 2 2019, 08:00 AM bbrock
[quote name='bbrock' post='2710466' date='May 2 2... May 2 2019, 08:21 AM jcd914
I mistakenly thought you were talking about the ... May 2 2019, 10:12 AM Mblizzard
I mistakenly thought you were talking about the... May 2 2019, 11:28 AM bbrock
[quote name='bbrock' post='2710483' date='May 2 2... May 2 2019, 11:38 AM Tdskip I won’t ask how you know Mike.
Grin. May 2 2019, 07:24 AM Tdskip I am assuming the do/don't on this is all writ... May 2 2019, 08:19 AM Tdskip So really only an issue if the fly wheel has been ... May 2 2019, 10:17 AM rhodyguy The run out on the fly wheel must be taken in to a... May 2 2019, 10:26 AM VaccaRabite Echoing what Mark said.
The dowel pin munching a m... May 2 2019, 10:46 AM worn
Or, in other words, where is a first time engine ... May 2 2019, 11:22 AM Superhawk996 is it just me misreading? I don't think dimen... May 2 2019, 11:59 AM rhodyguy I was under the impression that 'C' is the... May 2 2019, 12:01 PM bbrock
I was under the impression that 'C' is th... May 2 2019, 01:45 PM sixnotfour
I was under the impression that 'C' is th... May 3 2019, 09:32 AM sjhenry1075 I echo Mark's post about cooling tin; it's... May 2 2019, 12:21 PM mepstein
I echo Mark's post about cooling tin; it... May 2 2019, 12:31 PM Tbrown4x4 I'm also confused by that diagram. Always thou... May 2 2019, 06:33 PM bbrock
I'm also confused by that diagram. Always tho... May 2 2019, 07:31 PM Mark Henry IIRC That diagram is for a 914/6 flywheel and isn... May 2 2019, 07:18 PM Superhawk996
IIRC That diagram is for a 914/6 flywheel and isn... May 3 2019, 05:22 AM Tbrown4x4 I agree. ^^^^
My machinist was all hung up on the... May 3 2019, 04:55 AM Tdskip Great stuff.
Short of splitting the case is there... May 3 2019, 10:01 AM Tdskip Good morning.
Came across this while doing more r... May 9 2019, 07:33 AM mepstein
Good morning.
Came across this while doing more ... May 9 2019, 10:36 AM Bleyseng Yes! Most cams are pretty worn after 75,000 mi... May 9 2019, 08:23 AM rhodyguy You will have to tap the case for the threaded plu... May 9 2019, 09:42 AM Tdskip Oh fine - steer me towards doing it right. Some he... May 9 2019, 10:45 AM sixnotfour
Oh fine - steer me towards doing it right. Some h... May 9 2019, 12:21 PM cuddy_k
Oh fine - steer me towards doing it right. Some h... May 9 2019, 01:57 PM Tdskip
Oh fine - steer me towards doing it right. Some ... May 9 2019, 02:02 PM Montreal914 I have really enjoyed Van Svenson's website fo... May 9 2019, 01:53 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st August 2025 - 12:14 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.