 Exhaust to head gasket removal, Help removeing the copper exhaust gasket |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Krohn |
 May 10 2019, 08:32 PM
Post
#1
|
|
Newbie  Group: Members Posts: 9 Joined: 6-November 14 From: Santa Barbara, CA Member No.: 18,091 Region Association: Southern California  |
Is there a magic trick or a special tool that's needed to remove the copper gasket from the head where the exhaust bolts?
I'm in the processing of cleaning (and more cleaning and more cleaning and more cleaning... ) from 50 years of oil leaks and in the process of partial disassembly for some push rod tube seal replacement, but after removing the head exchangers, I haven't found a reasonable way of removing the copper gaskets from the head. Any helpful experience or out there? |
   |
 
|
  |
Replies
| Mark Henry |
May 10 2019, 09:09 PM
Post
#2
|
|
that's what I do! Group: Members Posts: 20,065 Joined: 27-December 02 From: Port Hope, Ontario Member No.: 26 Region Association: Canada |
Old flat screwdriver, heat the tip cherry red and bend the tip 90 degrees.
Hook it on the edge of the gasket and pull down. I have several pry and install tools made from old screwdrivers like this. |
|
|
|
| r_towle |
May 12 2019, 08:37 AM
Post
#3
|
|
Custom Member Group: Members Posts: 24,705 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States 
|
QUOTE(Mark Henry @ May 10 2019, 10:09 PM)  Old flat screwdriver, heat the tip cherry red and bend the tip 90 degrees. Hook it on the edge of the gasket and pull down. I have several pry and install tools made from old screwdrivers like this. several is because you lose them, and have to make another one. I know.... Rich |
|
|
|
| Superhawk996 |
May 12 2019, 08:45 AM
Post
#4
|
|
914 Guru Group: Members Posts: 7,255 Joined: 25-August 18 From: Woods of N. Idaho Member No.: 22,428 Region Association: Galt's Gulch
|
QUOTE(r_towle @ May 12 2019, 10:37 AM) QUOTE(Mark Henry @ May 10 2019, 10:09 PM) Old flat screwdriver, heat the tip cherry red and bend the tip 90 degrees. Hook it on the edge of the gasket and pull down. I have several pry and install tools made from old screwdrivers like this. several is because you lose them, and have to make another one. I know.... Rich (IMG:style_emoticons/default/av-943.gif) So true. I have multiples of tools just so when I misplace one, I don't have to stop working to look for it. They always turn up in some strange place when I'm doing clean up! |
 |
|
Posts in this topic
Krohn Exhaust to head gasket removal May 10 2019, 08:32 PM
Superhawk996 I have a small pick shaped tool with a slight bend... May 11 2019, 07:52 AM porschetub Be very careful removing these,if you damage the m... May 11 2019, 03:50 PM
Rand http://www.914world.com/bbs2/uploads_offsite/shop.... May 11 2019, 03:55 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st August 2025 - 05:22 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.