 Could use a hand..., First time motor pull.... |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Tjmrfe |
 Jun 12 2019, 09:23 AM
Post
#1
|
|
NON IMPEDING RATIONE COGITATIONIS  Group: Members Posts: 132 Joined: 10-April 15 From: Cornwall on Hudson, New York Member No.: 18,612 Region Association: North East States  |
Hey Guys, couldn’t take the leaking oil anymore....so, in a bold move, I decided to pull the motor! I’ve got everything sorted, all my ground straps and wiring is off...went down the check list, got my Tangerine plate and my dolly...now all I need is a guide, or two?...I’m more than willing to throw a BBQ together and refreshments I’m thinking the second weekend in July? 13/14....either day works...should not take too long, just four bolts right? Lol...I’m in Cornwall NY near West Point...PM me if you’ve got a free few hours that weekend, this way I can get it out and see how bad the oil leaks are!...
 |
   |
 
|
  |
Replies
| bdstone914 |
Jun 13 2019, 07:00 AM
Post
#2
|
|
bdstone914 Group: Members Posts: 5,280 Joined: 8-November 03 From: Riverside CA Member No.: 1,319 |
@Tjmrfe
I would be very interested to see if the Quik Jack can lift the car high enough to clear the engine coming out the back. Removing the filler neck reduces the engine hieght. It can be done alone but it good to have a helper to watch that it comes out well with nothing catching. And do you have those rubber blocks for thto give a couples inches more height. Bruce |
|
|
|
| iankarr |
Jun 13 2019, 07:33 AM
Post
#3
|
|
The wrencher formerly known as Cuddy_K Group: Members Posts: 2,595 Joined: 22-May 15 From: Heber City, UT Member No.: 18,749 Region Association: Intermountain Region 
|
QUOTE(bdstone914 @ Jun 13 2019, 09:00 AM)  @Tjmrfe I would be very interested to see if the Quik Jack can lift the car high enough to clear the engine coming out the back. Removing the filler neck reduces the engine hieght. It can be done alone but it good to have a helper to watch that it comes out well with nothing catching. And do you have those rubber blocks for thto give a couples inches more height. Bruce Hey Bruce... Yep. I've been doing it with Quick Jack. With the standard blocks you just have to take off the rear valance. |
|
|
|
| VaccaRabite |
Jun 13 2019, 10:30 AM
Post
#4
|
|
En Garde! Group: Admin Posts: 13,845 Joined: 15-December 03 From: Dallastown, PA Member No.: 1,435 Region Association: MidAtlantic Region
|
QUOTE(cuddy_k @ Jun 13 2019, 09:33 AM) QUOTE(bdstone914 @ Jun 13 2019, 09:00 AM) @Tjmrfe I would be very interested to see if the Quik Jack can lift the car high enough to clear the engine coming out the back. Removing the filler neck reduces the engine hieght. It can be done alone but it good to have a helper to watch that it comes out well with nothing catching. And do you have those rubber blocks for thto give a couples inches more height. Bruce Hey Bruce... Yep. I've been doing it with Quick Jack. With the standard blocks you just have to take off the rear valance. I bet if you only put blocks on the rear that would be enough angle to not have to remove the valence. The Quickjacks that I have used have all been taller then my 3 ton jack. IIRC you need 19 inches off the floor to get the engine out. Zach |
|
|
|
Posts in this topic
Tjmrfe Could use a hand... Jun 12 2019, 09:23 AM
ndfrigi you’re almost there to drop your engine. For su... Jun 12 2019, 09:31 AM
Tjmrfe
you’re almost there to drop your engine. For s... Jun 12 2019, 09:43 AM JOEPROPER I wish I had some time. I could use a drive over ... Jun 12 2019, 10:07 AM rhodyguy I use the 2 jack method raising under the control ... Jun 12 2019, 10:34 AM rgolia I think a group of 914 guys are meeting in Chester... Jun 12 2019, 01:23 PM Big Len We'll figure out a way to help you out. PM you... Jun 12 2019, 02:54 PM cuddy_k I’m in northern Westchester and am happy to come... Jun 12 2019, 03:03 PM injunmort i'm free. lets do it before mid july, then you... Jun 12 2019, 04:02 PM Big Len
i'm free. lets do it before mid july, then yo... Jun 12 2019, 04:58 PM rhodyguy Problem solved!!! Great bunch of peopl... Jun 12 2019, 04:23 PM Tjmrfe
Problem solved!!! Great bunch of peop... Jun 13 2019, 05:58 AM dabird I grew up in Orange County, NY. This thread is mak... Jun 12 2019, 04:34 PM rgalla9146 I saw Ian at Bear Mt. tonight and he mentioned you... Jun 12 2019, 07:57 PM bigkensteele I do it by myself. I use a jack under the engine ... Jun 12 2019, 08:31 PM Tjmrfe Wow, as expected, you guys couldn’t have been mo... Jun 13 2019, 05:26 AM mepstein Get a Tangerine jack plate and make it an easy, on... Jun 13 2019, 05:39 AM BeatNavy Most people only regret not buying one sooner.
... Jun 13 2019, 05:52 AM Tjmrfe
Get a Tangerine jack plate and make it an easy, o... Jul 13 2019, 06:14 PM IronHillRestorations +1 on the Tangerine engine plate, but you'd ne... Jun 13 2019, 06:45 AM Tjmrfe
[b]@[url=http://www.914world.com/bbs2/index.php?s... Jul 13 2019, 04:43 PM Tjmrfe
[b]@[url=http://www.914world.com/bbs2/index.php?s... Jul 13 2019, 06:17 PM cuddy_k Actually...using the tall blocks that come with th... Jun 13 2019, 01:11 PM Tjmrfe
Actually...using the tall blocks that come with t... Jun 13 2019, 02:34 PM Bleyseng :popcorn: Jul 14 2019, 11:05 AM SirAndy Bit late to the party but we do have a nice write-... Jul 14 2019, 11:23 AM Tjmrfe
Bit late to the party but we do have a nice write... Jul 15 2019, 06:20 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd April 2026 - 02:52 PM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.