Help please! alignment specs ? |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Help please! alignment specs ? |
PatrickB |
Aug 2 2019, 06:52 AM
Post
#1
|
Member Group: Members Posts: 249 Joined: 26-March 17 From: sw ontario Member No.: 20,960 Region Association: Canada |
At a shop to check alignment after some work. They don't have a spec for 914's . They do have 911 specs.... anyone know if they are the same ? I wouldn't think so but....
Can anyone point |
Gatornapper |
Aug 2 2019, 07:04 AM
Post
#2
|
Senior Member Group: Members Posts: 1,235 Joined: 22-September 17 From: Woods west of Richmond, VA Member No.: 21,449 Region Association: South East States |
At a shop to check alignment after some work. They don't have a spec for 914's . They do have 911 specs.... anyone know if they are the same ? I wouldn't think so but.... Can anyone point From 1976 Owner's Manual: Camber - Front: 0 deg. +/- 20' Rear: 30 deg. +/- 20' Toe-in: Front: +20' +/- 10' Rear: 0 deg. +15' (w/33 lbs. curb weight added) Caster angle (at curb weight): 6 deg. +/- 30' GN |
dr914@autoatlanta.com |
Aug 2 2019, 09:12 AM
Post
#3
|
914 Guru Group: Members Posts: 7,896 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
It is 30 MINUTES neg camber in the rear and 0 in the front.
Make sure that you have correct height in the rear so you will not have to stack too many shims to achieve camber. (basically show three inches of tire between the wheel rim and the fender lip At a shop to check alignment after some work. They don't have a spec for 914's . They do have 911 specs.... anyone know if they are the same ? I wouldn't think so but.... Can anyone point From 1976 Owner's Manual: Camber - Front: 0 deg. +/- 20' Rear: 30 deg. +/- 20' Toe-in: Front: +20' +/- 10' Rear: 0 deg. +15' (w/33 lbs. curb weight added) Caster angle (at curb weight): 6 deg. +/- 30' GN |
SirAndy |
Aug 2 2019, 10:59 AM
Post
#4
|
Resident German Group: Admin Posts: 41,679 Joined: 21-January 03 From: Oakland, Kalifornia Member No.: 179 Region Association: Northern California |
It is 30 MINUTES neg camber in the rear and 0 in the front. Camber - Front: 0 deg. +/- 20' Rear: 30 deg. +/- 20' 30 degrees would be a wee bit much ... (IMG:style_emoticons/default/biggrin.gif) |
SirAndy |
Aug 2 2019, 03:39 PM
Post
#5
|
Resident German Group: Admin Posts: 41,679 Joined: 21-January 03 From: Oakland, Kalifornia Member No.: 179 Region Association: Northern California |
I just googled "excessive camber" and was not disappointed. Apparently, this really is a thing! (IMG:style_emoticons/default/unsure.gif) https://www.google.com/search?q=excessive+c...661&bih=875 . .. |
Superhawk996 |
Aug 3 2019, 04:00 AM
Post
#6
|
914 Guru Group: Members Posts: 5,903 Joined: 25-August 18 From: Woods of N. Idaho Member No.: 22,428 Region Association: Galt's Gulch |
I just googled "excessive camber" and was not disappointed. Apparently, this really is a thing! (IMG:style_emoticons/default/unsure.gif) https://www.google.com/search?q=excessive+c...661&bih=875 . .. (IMG:style_emoticons/default/confused24.gif) (IMG:style_emoticons/default/av-943.gif) If something can be done in bad taste, there is always someone willing to up the ante and take it to the extreme no matter how undrivable it might be! |
ClayPerrine |
Aug 4 2019, 07:51 AM
Post
#7
|
Life's been good to me so far..... Group: Admin Posts: 15,520 Joined: 11-September 03 From: Hurst, TX. Member No.: 1,143 Region Association: NineFourteenerVille |
I just googled "excessive camber" and was not disappointed. Apparently, this really is a thing! (IMG:style_emoticons/default/unsure.gif) https://www.google.com/search?q=excessive+c...661&bih=875 . .. (IMG:style_emoticons/default/confused24.gif) (IMG:style_emoticons/default/av-943.gif) If something can be done in bad taste, there is always someone willing to up the ante and take it to the extreme no matter how undrivable it might be! It is called "Stance" and apparently it is a fad these days. (IMG:style_emoticons/default/screwy.gif) Negative camber is good if you are racing, but most cars don't spend all their time in hard corners. So all it does is over stresses the sidewalls of the tires and eats up the wheel bearings. Plus, even for racing you don't need that much camber. Wikipedia link on Stanced cars "Form is greater than function in stance culture." " In the stance community, some owners run up to 45° of negative camber to achieve the stance they are looking for." Just a fad, like the tiny tires stuck way outside the fenders, Donks, and alike. |
JamesM |
Aug 8 2019, 07:08 AM
Post
#8
|
Senior Member Group: Members Posts: 1,915 Joined: 6-April 06 From: Kearns, UT Member No.: 5,834 Region Association: Intermountain Region |
It is called "Stance" and apparently it is a fad these days. "Form is greater than function in stance culture." Its been big around here for a while (actually think its starting to go away, thank god) I never thought someone would come up with a more ridiculous car trend than the "fast and furious" coffee can exhaust cars in 90s, but they somehow managed. Not sure what is worse, what they do with the camber or what they do to their poor tires. Both form and function is just terrible. |
Lo-Fi Version | Time is now: 10th June 2024 - 01:11 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |