 Gluing trunk/frunk skins to frame, Need ahesive recommendation |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| bbrock |
 Sep 8 2019, 06:18 PM
Post
#1
|
|
914 Guru  Group: Members Posts: 5,269 Joined: 17-February 17 From: Montana Member No.: 20,845 Region Association: Rocky Mountains 
 |
Doing a bit of rehab on my front trunk lid in preparation for paint. One side of the A-frame member is stuck tight to the skin but the other side has lifted off about 3/32". I want to glue the lifted side down but don't know what adhesive would work best. 3M Panel Bonding Adhesive looks like it would be the ultimate but kind of expensive and probably overkill for this application. Any suggestions?
 |
   |
 
|
  |
Replies
| Garland |
Sep 10 2019, 09:05 AM
Post
#2
|
|
Restoration Fanatic Group: Members Posts: 1,411 Joined: 8-January 04 From: ......Michigan...... Member No.: 1,535 Region Association: Upper MidWest
|
Try this stuff it loves 914
Attached image(s) 
|
|
|
|
| bbrock |
Sep 10 2019, 09:08 AM
Post
#3
|
|
914 Guru Group: Members Posts: 5,269 Joined: 17-February 17 From: Montana Member No.: 20,845 Region Association: Rocky Mountains
|
QUOTE(Garland @ Sep 10 2019, 09:05 AM)  Try this stuff it loves 914 I need to actually bond the skin to the frame in a section where it has lifted away. I not sure if seam sealer will have the proper "stick" needed. |
|
|
|
Posts in this topic
bbrock Gluing trunk/frunk skins to frame Sep 8 2019, 06:18 PM
raynekat I would think any kind of "2 part" epoxy... Sep 8 2019, 07:24 PM
worn I never knew they were bonded there. Thanks. Mak... Sep 8 2019, 08:42 PM bbrock
I never knew they were bonded there. Thanks. Ma... Sep 8 2019, 10:14 PM bbrock I think I'm going to pick up a tube of this 3M... Sep 10 2019, 08:41 AM burton73 Brent buddy,
You need to think this out. The heat... Sep 10 2019, 09:59 AM Garland
Brent buddy,
You need to think this out. The hea... Sep 10 2019, 12:00 PM SirAndy :welder: Sep 10 2019, 12:07 PM Bartlett 914 Before committing to glue, I would make sure the h... Sep 10 2019, 12:09 PM amfab I used the 3M Panel bonding adhesive for this, its... Sep 10 2019, 02:10 PM bbrock All, Thanks for the suggestions. Let me explain ... Sep 10 2019, 03:14 PM Jeff Hail If you are going to use anything use anti-flutter ... Sep 11 2019, 08:09 AM bbrock Thanks Jeff and Andrew. I had never heard of anit... Sep 11 2019, 08:52 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 02:47 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.