 Drilling the rotors....., whats a guy to do? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| xsboost90 |
 Dec 4 2004, 10:52 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,393 Joined: 2-August 04 From: cincinnati Member No.: 2,432  |
so my eric shea rear hubs are here, and now im just left to find some lug nuts and some five lug rear rotors. The guy i bought my motor from said to just bolt my adapter on and drill it out by hand. Is this a good idea? Is there a rotor from something else that is the same but five lug? THis is for the REAR.
Attached image(s) 
|
   |
 
|
  |
Replies
| Mueller |
Dec 4 2004, 10:56 AM
Post
#2
|
|
914 Freak! Group: Members Posts: 17,146 Joined: 4-January 03 From: Antioch, CA Member No.: 87 Region Association: None 
|
for the rear rotors, just re-drilling them is fine...when it comes time to get new rotors, just buy the /6 rotors which have the correct 5x130 pattern already
you don't have to be super accurate since the wheels are located by the studs.... you might want to redrill them so that you can still use the 2 little screws to hold the rotor onto the hub... |
|
|
|
Posts in this topic
xsboost90 Drilling the rotors..... Dec 4 2004, 10:52 AM
xsboost90 so the 6 rear rotors arent vented or offset differ... Dec 4 2004, 11:00 AM Mueller I'm 90% sure they are not vented and the offse... Dec 4 2004, 11:12 AM Dave_Darling The Six rotors are not vented, they are not offset... Dec 4 2004, 11:28 AM ! They run like $50....just like a Hummer.... :... Dec 4 2004, 11:38 AM Eric_Shea QUOTE
muddboy I have!
On a car I purchased I had a really b... Dec 6 2004, 12:29 AM Qarl Woohoo! :mueba: :mueba: :mueba: :mueba: ... Dec 6 2004, 12:33 AM MattR I did the exact same thing (I went from rivs to ph... Dec 6 2004, 12:36 AM Eric_Shea Thanks Muddboy,
It would be cool to have an answe... Dec 6 2004, 10:06 AM muddboy El Faralito?....
The car is a '73 that it hap... Dec 6 2004, 10:49 PM joea9146 My car is a 75 had to grind down the 914/6 rotors ... Dec 7 2004, 06:48 AM r_towle what are erics hubs?????
I looked in the resource... Dec 7 2004, 11:00 AM Eric_Shea these? (I guess I should stick them in the Resour... Dec 7 2004, 11:50 AM Series9 I have done a few 5-bolt conversions using redrill... Dec 7 2004, 12:33 PM
dcicchetto914 Eric:
I looked at your stuff in resource section.... Mar 3 2005, 09:26 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 16th June 2024 - 05:35 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.