 Jacking point damage? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Biggles |
 Mar 25 2020, 10:00 AM
Post
#1
|
|
Member  Group: Members Posts: 200 Joined: 5-September 13 From: UK Member No.: 16,353 Region Association: England  |
I've noticed that the front jacking points on my car aren't level, and wondered if they've gone up as the car has been lifted - thoughts? It all seems solid.
Attached thumbnail(s)  
|
   |
 
|
  |
Replies
| Retroracer |
Jul 6 2020, 05:44 PM
Post
#2
|
|
Senior Member Group: Members Posts: 640 Joined: 7-July 13 From: Bend OR Member No.: 16,100 Region Association: Pacific Northwest 
|
Donut jacking: interesting reading for me.
Early on in my build when fixing rust, dents, adding stiffening, etc. I used the rear donuts to jack the car almost all the time. I remember trying to jack it up using one of the front donuts once, and was shocked to notice the floor deforming! I quickly dropped it, "persuaded" that section of the floor back into place - this was before paint remember - and decided never to jack up the car on the front donuts ever again. I still routinely use the rear donuts to jack the car, then use a wrapped wooden spreader along the rocker (sill) area to take the load with a jack stand. Not seen any deformation around the rear donuts thus far. - Tony PS. @euro911 : LOL |
|
|
|
Posts in this topic
Biggles Jacking point damage? Mar 25 2020, 10:00 AM
SirAndy They are crooked because those aren't jacking ... Mar 25 2020, 10:15 AM
Biggles
They are crooked because those aren't jacking... Mar 25 2020, 10:29 AM
dr914@autoatlanta.com jack under the engine mounting bar, or the front c... Mar 25 2020, 10:37 AM Biggles Cheers George. No engine mounting bar. It's a ... Mar 25 2020, 11:13 AM bkrantz
They are crooked because those aren't jacking... Mar 25 2020, 08:29 PM 914e
They are crooked because those aren't jackin... Mar 25 2020, 09:32 PM bretth I thought all four doughnuts were for jacking up/s... Mar 25 2020, 11:05 AM SirAndy The donuts were used to suspend the cars on the as... Mar 25 2020, 11:17 AM Biggles
The donuts were used to suspend the cars on the a... Mar 25 2020, 11:18 AM ctc911ctc SirAndy! MORE OF THESE FACTORY PICTURES PLEAS... Mar 25 2020, 04:47 PM SirAndy And if you check the location of the donuts in the... Mar 25 2020, 11:19 AM kroelofsen
And if you check the location of the donuts in th... Mar 25 2020, 02:12 PM wes I saved this year’s back from here. Mar 25 2020, 11:58 AM gandalf_025 You can see the point on the floor ,in front of
th... Mar 25 2020, 03:14 PM rgalla9146
You can see the point on the floor ,in front of
t... Mar 25 2020, 04:34 PM mbseto So aside from accuracy, there's no reason to r... Mar 25 2020, 04:59 PM bretth I think if it was designed to hang the whole car o... Mar 25 2020, 06:13 PM drem914 If those are not where we are suppose to jack the ... Mar 25 2020, 06:49 PM cuddy_k
If those are not where we are suppose to jack the... Mar 26 2020, 12:10 AM drem914
If those are not where we are suppose to jack th... Mar 26 2020, 10:02 PM SO.O.C914er I agree these are the jack points if they are not ... Mar 25 2020, 07:25 PM Biggles Based on the responses, the fact the rear donuts /... Mar 26 2020, 03:25 AM euro911 RE: Jacking point damage? Jul 6 2020, 11:49 AM euro911 Here's a site that has pix & videos ... ht... Jul 6 2020, 01:30 PM Cairo94507 Jesus.....what is the best way to lift a 914 w/o d... Jul 6 2020, 05:50 PM euro911 Jesus.....what is the best way to lift a 914 w/o d... Jul 6 2020, 11:38 PM mepstein
Jesus.....what is the best way to lift a 914 w/o ... Jul 7 2020, 06:17 AM MM1 Sir Andy,
Is it possible for you to elucidate my ... Jul 6 2020, 06:34 PM Cairo94507 OK- I have a few hockey pucks and several other li... Jul 7 2020, 06:32 AM MM1 Thanks, Gents!
Mark - so when jacking the fro... Jul 7 2020, 09:31 AM mepstein
Thanks, Gents!
Mark - so when jacking the fr... Jul 7 2020, 10:45 AM MM1
Thanks, Gents!
Mark - so when jacking the f... Jul 8 2020, 09:52 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st July 2025 - 12:51 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.