 Clutch cable adjustment, Not getting anywhere. |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Mcraneiowa |
 Aug 16 2020, 01:15 PM
Post
#1
|
|
Member  Group: Members Posts: 82 Joined: 16-June 20 From: IA Member No.: 24,387 Region Association: None  |
I’m sure this has been covered before but I was not able to find what exactly was of help. I read in one post I should have about 1/8” of up/down travel on the cable to suggest proper tension. I have adjusted it in and out and everywhere in between to no avail. With the engine running I am not able to put the car into either first or reverse without grinding. I do not see any movement of the clutch housing inside of the tunnel, so I don’t think that is the issue. I have a brand new cable installed and other than trying to get the car to move,, this is far as the cable has been used. I can see the arm pulling in and out on the transaxle as well when depressing the clutch. Anyone have an idea of what I am missing here. Looking for suggestions.
|
   |
 
|
  |
Replies
| Tdskip |
Aug 16 2020, 01:21 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 3,736 Joined: 1-December 17 From: soCal Member No.: 21,666 Region Association: None 
|
QUOTE(Mcraneiowa @ Aug 16 2020, 02:15 PM)  I’m sure this has been covered before but I was not able to find what exactly was of help. I read in one post I should have about 1/8” of up/down travel on the cable to suggest proper tension. I have adjusted it in and out and everywhere in between to no avail. With the engine running I am not able to put the car into either first or reverse without grinding. I do not see any movement of the clutch housing inside of the tunnel, so I don’t think that is the issue. I have a brand new cable installed and other than trying to get the car to move,, this is far as the cable has been used. I can see the arm pulling in and out on the transaxle as well when depressing the clutch. Anyone have an idea of what I am missing here. Looking for suggestions. Are you sure that it isn’t a shifter alignment issue? Can get 2-5 cleanly? |
 |
|
Posts in this topic
Mcraneiowa Clutch cable adjustment Aug 16 2020, 01:15 PM
Mcraneiowa I am not able to get into either 2nd or 5th. I ha... Aug 16 2020, 01:32 PM
Tdskip
I am not able to get into either 2nd or 5th. I h... Aug 16 2020, 01:34 PM rhodyguy Which gears can you cleanly engage with the motor ... Aug 16 2020, 01:42 PM Mcraneiowa I asked my wife to double check as I watched the m... Aug 16 2020, 01:50 PM wndsrfr
I would think if I had the cable adjusted prope... Aug 16 2020, 07:15 PM rhodyguy There's a spring loaded plate in the shift lev... Aug 16 2020, 02:03 PM Mcraneiowa Just to clarify it’s a 1974 1.8 L with a side sh... Aug 16 2020, 02:05 PM Mcraneiowa Double checked shift pattern, both set screws and ... Aug 16 2020, 02:21 PM Mcraneiowa So I may be making too large of an adjustment and ... Aug 16 2020, 07:42 PM Tdskip The clutch and shifter on these is wildly differen... Aug 16 2020, 09:52 PM Mcraneiowa The only thing that comes to mind is how the cable... Aug 17 2020, 01:48 AM falcor75 I changed to a new clutch cable this winter and I ... Aug 17 2020, 02:07 AM ctc911ctc This may be helpful as to what to check to see if ... Aug 17 2020, 06:57 PM Tdskip Did you get this sorted? Aug 18 2020, 03:56 PM Mcraneiowa I finally resolved my issue. I believe since thi... Aug 19 2020, 05:15 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 09:54 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.