 IDF Weber with hex bar - linkage towards front or rear of car? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Tdskip |
 Oct 9 2020, 07:33 AM
Post
#1
|
|
Advanced Member  Group: Members Posts: 3,686 Joined: 1-December 17 From: soCal Member No.: 21,666 Region Association: None 
 |
I've heard it both ways (nod to any Psych fans out there), and preferred orientation of the linkage?
Thanks! |
   |
 
|
  |
Replies
| Ansbacher |
Oct 10 2020, 06:54 PM
Post
#2
|
|
Senior Member Group: Members Posts: 689 Joined: 4-July 14 From: Tampa Bay, Florida Member No.: 17,589 |
So...to do a swap from front to back or vice-versa, does that mean the carbs get switched left to right and mounted backwards from the original installation?? I just can't wrap my head around all this.
Ansbacher |
|
|
|
| Tdskip |
Oct 11 2020, 07:06 AM
Post
#3
|
|
Advanced Member Group: Members Posts: 3,686 Joined: 1-December 17 From: soCal Member No.: 21,666 Region Association: None
|
QUOTE(Ansbacher @ Oct 10 2020, 07:54 PM)  So...to do a swap from front to back or vice-versa, does that mean the carbs get switched left to right and mounted backwards from the original installation?? I just can't wrap my head around all this. Ansbacher The carbs would be swapped and flipped around side to side if you move the hex bar to the front of the car, fuel line place,emt changes some too. |
|
|
|
Posts in this topic
Tdskip IDF Weber with hex bar - linkage towards front or rear of car? Oct 9 2020, 07:33 AM
Mark Henry
... preferred orientation of the hex bar linkage?... Oct 9 2020, 07:45 AM
Tdskip
... preferred orientation of the hex bar linkage... Oct 9 2020, 08:11 AM 914werke ... preferred orientation of the hex bar linkage... Oct 9 2020, 09:28 AM rhodyguy On the front. PITA standing on your head dialing t... Oct 9 2020, 11:32 AM Spoke I had the bar connected towards the rear but the l... Oct 9 2020, 12:08 PM Tdskip Thanks for the responses - just need to get this o... Oct 9 2020, 01:14 PM ndfrigi
Thanks for the responses - just need to get this ... Oct 9 2020, 01:29 PM Ansbacher I have a hex bar linkage and am confused by this w... Oct 9 2020, 02:25 PM rhodyguy The forward side of the carbs.
Throw the cross ba... Oct 9 2020, 02:41 PM Ansbacher I think if I tried to put it in front of my carbs,... Oct 9 2020, 02:55 PM nditiz1 Towards the front of the car. If you are just try... Oct 10 2020, 11:35 AM Tdskip Thanks for all of the responses. I just need to ge... Oct 10 2020, 02:17 PM Gint A lot of it depends on what other junk is in your ... Oct 10 2020, 03:00 PM Gint Carbs swapped, no. You would have to take the end... Oct 11 2020, 12:35 PM Tdskip
Carbs swapped, no. You would have to take the en... Oct 11 2020, 12:44 PM Gint Carbs swapped, no. You would have to take the end... Oct 11 2020, 01:07 PM Gint Ok, whatever works for you. That would mean your ... Oct 11 2020, 12:50 PM Tdskip Thanks for all of the responses and discussion, in... Oct 11 2020, 02:42 PM Gint Info, exchange of information and ideas never hurt... Oct 11 2020, 02:50 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st June 2024 - 10:09 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.