 IDF Weber with hex bar - linkage towards front or rear of car? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Tdskip |
 Oct 9 2020, 07:33 AM
Post
#1
|
|
Advanced Member  Group: Members Posts: 3,686 Joined: 1-December 17 From: soCal Member No.: 21,666 Region Association: None 
 |
I've heard it both ways (nod to any Psych fans out there), and preferred orientation of the linkage?
Thanks! |
   |
 
|
  |
Replies
| Gint |
Oct 11 2020, 12:35 PM
Post
#2
|
|
Mike Ginter Group: Admin Posts: 16,083 Joined: 26-December 02 From: Denver CO. Member No.: 20 Region Association: Rocky Mountains  |
Carbs swapped, no. You would have to take the ends off of the shafts and swap them over to the other side of the carb if memory serves me correctly. It was a long time ago that I last did it. I don't even know where my old cross bar linkage went to.
|
|
|
|
| Tdskip |
Oct 11 2020, 12:44 PM
Post
#3
|
|
Advanced Member Group: Members Posts: 3,686 Joined: 1-December 17 From: soCal Member No.: 21,666 Region Association: None
|
QUOTE(Gint @ Oct 11 2020, 01:35 PM)  Carbs swapped, no. You would have to take the ends off of the shafts and swap them over to the other side of the carb if memory serves me correctly. It was a long time ago that I last did it. I don't even know where my old cross bar linkage went to. Was easier to swap the carbs side to side since in my case everything was loose fitted - did that last week. |
|
|
|
Posts in this topic
Tdskip IDF Weber with hex bar - linkage towards front or rear of car? Oct 9 2020, 07:33 AM
Mark Henry
... preferred orientation of the hex bar linkage?... Oct 9 2020, 07:45 AM
Tdskip
... preferred orientation of the hex bar linkage... Oct 9 2020, 08:11 AM 914werke ... preferred orientation of the hex bar linkage... Oct 9 2020, 09:28 AM rhodyguy On the front. PITA standing on your head dialing t... Oct 9 2020, 11:32 AM Spoke I had the bar connected towards the rear but the l... Oct 9 2020, 12:08 PM Tdskip Thanks for the responses - just need to get this o... Oct 9 2020, 01:14 PM ndfrigi
Thanks for the responses - just need to get this ... Oct 9 2020, 01:29 PM Ansbacher I have a hex bar linkage and am confused by this w... Oct 9 2020, 02:25 PM rhodyguy The forward side of the carbs.
Throw the cross ba... Oct 9 2020, 02:41 PM Ansbacher I think if I tried to put it in front of my carbs,... Oct 9 2020, 02:55 PM nditiz1 Towards the front of the car. If you are just try... Oct 10 2020, 11:35 AM Tdskip Thanks for all of the responses. I just need to ge... Oct 10 2020, 02:17 PM Gint A lot of it depends on what other junk is in your ... Oct 10 2020, 03:00 PM Ansbacher So...to do a swap from front to back or vice-versa... Oct 10 2020, 06:54 PM Tdskip
So...to do a swap from front to back or vice-vers... Oct 11 2020, 07:06 AM Gint Carbs swapped, no. You would have to take the end... Oct 11 2020, 01:07 PM Gint Ok, whatever works for you. That would mean your ... Oct 11 2020, 12:50 PM Tdskip Thanks for all of the responses and discussion, in... Oct 11 2020, 02:42 PM Gint Info, exchange of information and ideas never hurt... Oct 11 2020, 02:50 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 7th June 2024 - 08:37 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.