 How to read amps on a multimeter, Trying to find a parasitic drain |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| ThinAir |
 Oct 20 2020, 11:49 PM
Post
#1
|
|
Best friends  Group: Members Posts: 2,543 Joined: 4-February 03 From: Flagstaff, AZ Member No.: 231 Region Association: Southwest Region 
 |
Electrical systems & I are not friends, so I have little experience with this. I don't know how to interpret these readings or how the range changes what I'm seeing. Searching has turned up lots of stuff that seems to assume that you know this. TIA for the advice.
  Both of these readings were taken with the circuit in the same state. (I thought I had one when set to the 400A range). |
   |
 
|
  |
Replies
| Mark Henry |
Oct 21 2020, 01:09 PM
Post
#2
|
|
that's what I do! Group: Members Posts: 20,065 Joined: 27-December 02 From: Port Hope, Ontario Member No.: 26 Region Association: Canada |
Ahh... Jwest or Engman?
I do know on the Engman there's been issues with the fuse block bridging. If you look at the pic, 45* left from the round relay you can see the back corner of the fuse cover popped up a bit. That all comes apart and you will find a bunch of circuits jumped with a wire. Peeps have had issues with the jumper wire and the wire is why the cover won't sit flat. |
|
|
|
| ThinAir |
Oct 21 2020, 01:13 PM
Post
#3
|
|
Best friends Group: Members Posts: 2,543 Joined: 4-February 03 From: Flagstaff, AZ Member No.: 231 Region Association: Southwest Region
|
QUOTE(Mark Henry @ Oct 21 2020, 12:09 PM)  Ahh... Jwest or Engman? I do know on the Engman there's been issues with the fuse block bridging. If you look at the pic, 45* left from the round relay you can see the back of the fuse cover popped up a bit. That all comes apart and you will find a bunch of circuits jumped with a wire. Peeps have had issues with the jumper wire and is why the cover won't sit flat. I'll check that out! |
|
|
|
Posts in this topic
ThinAir How to read amps on a multimeter Oct 20 2020, 11:49 PM
tom.esh Top display looks to be .63 amps. Bottom display i... Oct 21 2020, 04:52 AM Tdskip @tom.esh - are you suggesting using the 200m sett... Oct 21 2020, 06:17 AM JOEPROPER Does that meter have a clamp or are you in series?... Oct 21 2020, 06:34 AM tom.esh yes, the 200ma setting should be fine. Oct 21 2020, 07:27 AM Mark Henry Volts A- set at 20, this will read in 12V range.
o... Oct 21 2020, 08:27 AM Mark Henry For parasitic drain pull all your fuses, try a fus... Oct 21 2020, 08:45 AM ThinAir Thanks guys! These meters are in series betwee... Oct 21 2020, 11:30 AM ctc911ctc Wait! The guy who started this thread and is ... Oct 21 2020, 12:30 PM
ThinAir
Wait! The guy who started this thread and is... Oct 21 2020, 01:11 PM ThinAir
Ahh... Jwest or Engman?
I do know on the Engman ... Oct 21 2020, 02:00 PM Mark Henry There is a reason, it's how the factory fuse b... Oct 21 2020, 05:01 PM ThinAir
There is a reason, it's how the factory fuse ... Oct 21 2020, 05:18 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 7th June 2024 - 09:36 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.