 Best way to remove tin bolts, Without break8ng them |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Mcraneiowa |
 Oct 19 2020, 06:25 PM
Post
#1
|
|
Member  Group: Members Posts: 82 Joined: 16-June 20 From: IA Member No.: 24,387 Region Association: None  |
Is it common practice to heat the little bolts holding the tin on the engiine in order to remove them. I have been soaking them with penetrating oil. Iask this is I don’t wanna get anything too hot and damage the engine case. Looking to see what others have done as I’ve already broken one I will have to tap it out just don’t wanna have to do more if I can help it
|
   |
 
|
  |
Replies
| IronHillRestorations |
Oct 21 2020, 07:58 PM
Post
#2
|
|
I. I. R. C. Group: Members Posts: 6,926 Joined: 18-March 03 From: West TN Member No.: 439 Region Association: None 
|
Back on topic. I too use a hand impact when I get a stubborn one. Most of the time I do OK with my largest Stahlwille metric screwdriver that has a hex shank at the top. I can lean on it pretty hard and get the torque with a wrench on the hex. FWIW, there's a difference between SAE and metric screw drivers
|
|
|
|
Posts in this topic
Mcraneiowa Best way to remove tin bolts Oct 19 2020, 06:25 PM
porschetub
Is it common practice to heat the little bolts ho... Oct 19 2020, 06:49 PM Gint I had one engine that was a PITA to get the tin sc... Oct 19 2020, 06:59 PM
AZBanks
I had one engine that was a PITA to get the tin s... Oct 20 2020, 01:44 AM 90quattrocoupe When you put them back in, anti-seize is your frie... Oct 20 2020, 12:38 AM GregAmy +1 on anti-seize, and replace them with something ... Oct 20 2020, 06:34 AM Amphicar770 When I pulled my engine I removed all of the tins ... Oct 20 2020, 09:37 AM Dobbsy Has anyone experienced galvanic corrosion when usi... Oct 20 2020, 11:05 AM IronHillRestorations
Has anyone experienced galvanic corrosion when us... Oct 20 2020, 11:06 AM Dobbsy
Has anyone experienced galvanic corrosion when u... Oct 20 2020, 11:27 AM IronHillRestorations
[quote name='IronHillRestorations' post='2860414'... Oct 21 2020, 07:32 PM 73-914
Has anyone experienced galvanic corrosion when u... Oct 20 2020, 02:30 PM rhodyguy MM :agree: . Coating, liberally, exhaust studs mak... Oct 20 2020, 02:44 PM Mark Henry I have a oxy/propane cutting torch, not as hot as ... Oct 20 2020, 05:02 PM Superhawk996
I have a oxy/propane cutting torch, not as hot as... Oct 20 2020, 05:21 PM Mark Henry
[quote name='Mark Henry' post='2860469' date='Oct... Oct 21 2020, 02:40 PM Superhawk996
[quote name='Mark Henry' post='2860469' date='Oc... Oct 21 2020, 03:12 PM SKL1 The 914 rubber ones are nice but I guess I prefer ... Oct 21 2020, 10:43 PM Frankvw MoM must be an American thing.....I use Ceramic Gr... Oct 22 2020, 03:04 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd April 2026 - 11:41 AM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.