 6 cylinder engine removal, Advice needed |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Dobbsy |
 Feb 10 2022, 03:02 PM
Post
#1
|
|
Newbie  Group: Members Posts: 49 Joined: 22-May 14 From: West Midlands Member No.: 17,382 Region Association: England 
 |
I have looked to see if this has been posted before but could not find a thread.
What is the best way to remove the engine and gearbox, is there a cradle like the one for the 4 cylinder. Should I remove the heat exchangers first or can I use them for support. |
   |
 
|
  |
Replies
| Dobbsy |
Feb 11 2022, 02:44 PM
Post
#2
|
|
Newbie Group: Members Posts: 49 Joined: 22-May 14 From: West Midlands Member No.: 17,382 Region Association: England
|
Thanks for all the replies and photos,
I will make cradle at the weekend. I have already raised the car up on blocks and have the use of a fork lift, this will allow me to safely lower the engine / gearbox onto a trolley. |
|
|
|
Posts in this topic
Dobbsy 6 cylinder engine removal Feb 10 2022, 03:02 PM
mb911
I have looked to see if this has been posted befo... Feb 10 2022, 03:14 PM mepstein I like using a lift table. I unbolt the handle and... Feb 10 2022, 03:26 PM SirAndy is there a cradle like the one for the 4 cylinder
... Feb 10 2022, 03:35 PM
infraredcalvin Factory tools, not cheap!
Feb 10 2022, 08:32 PM Superhawk996 Shame Tangerine Racing doesn't offer a nice pl... Feb 10 2022, 04:04 PM Tdskip Harbor Freight lifting table makes it easy - just ... Feb 10 2022, 04:48 PM mepstein
Harbor Freight lifting table makes it easy - just... Feb 10 2022, 05:32 PM johnhora I agree with the group that the Harbor Freight hea... Feb 10 2022, 05:41 PM sixaddict I have used this many times……makes it a one ma... Feb 13 2022, 11:19 AM Eric_Shea We have 3 of the lift tables. Install the handle ... Feb 10 2022, 06:03 PM targa72e I use 3 low profile jacks. Works for both 911 and ... Feb 10 2022, 10:31 PM ClayPerrine I just set the motor and trans on jackstands, and ... Feb 11 2022, 08:07 AM Dion I took the left side tin off. A little more wiggl... Feb 11 2022, 08:12 AM 9146C As already mentioned, with the HE's installed,... Feb 11 2022, 08:18 AM brant I prefer the lift
I have a wheeled platform for p... Feb 11 2022, 08:37 AM zoomCat Does anybody have any experience using a QuickJack... Feb 11 2022, 09:16 AM mlindner Dobbsy, I built a engine cradle to support engine ... Feb 11 2022, 01:40 PM rgalla9146 What a bunch of sissies ! Way too fussy.
... Feb 11 2022, 07:00 PM bkrantz
What a bunch of sissies ! Way too fussy.
... Feb 11 2022, 09:27 PM brant A wooden box with casters can come in handy for lo... Feb 13 2022, 10:55 AM mlindner brant, I like your shop, very cool. Feb 13 2022, 10:57 AM brant
brant, I like your shop, very cool.
Thank you... Feb 13 2022, 05:37 PM mepstein I had modified my lift table arms once before but ... Feb 13 2022, 11:36 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 11:56 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.