 I was bored so decided to drop the engine, Oh my!! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| BK911 |
 Feb 17 2022, 11:42 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 672 Joined: 19-February 04 From: Rocky Top, TN Member No.: 1,674 Region Association: None  |
So many oil leaks.
Even had oil mist out the windshield defrost vent! What causes so much oil around the cylinder/case interface? Pretty wet on both sides.  Side where I attached the oil breather to air cleaner has built up oil on back side of intake valves!!  Have to figure out a better way for head and case vent. On a positive note, 6 8 6 6 % leakdown!! |
   |
 
|
  |
Replies
| DRPHIL914 |
Feb 17 2022, 01:32 PM
Post
#2
|
|
Dr. Phil Group: Members Posts: 5,769 Joined: 9-December 09 From: Bluffton, SC Member No.: 11,106 Region Association: South East States 
|
QUOTE(BK911 @ Feb 17 2022, 12:42 PM)  So many oil leaks. Even had oil mist out the windshield defrost vent! What causes so much oil around the cylinder/case interface? Pretty wet on both sides. Side where I attached the oil breather to air cleaner has built up oil on back side of intake valves!! Have to figure out a better way for head and case vent. On a positive note, 6 8 6 6 % leakdown!! check you head bolt torque, if you have good leak down and compression was good, then rings should be ok, but you’d get some oil leaking by case/cylinder interface over time the loosen- 4 years ago when i pulled mine to paint, mine were only 12-15ft# should be 25 or 27# i believe, no leaking after that- |
|
|
|
Posts in this topic
BK911 I was bored so decided to drop the engine Feb 17 2022, 11:42 AM
GregAmy Oh-oh....the dreaded "As Long As Syndrome... Feb 17 2022, 11:56 AM Chris H. AKA "DWD", "Dirk Wright's disea... Feb 17 2022, 12:13 PM Root_Werks Ignorance is bliss!
That'd be a tough one... Feb 17 2022, 12:46 PM BK911 Imma gonna clean it up and put it back in!
Jus... Feb 17 2022, 12:57 PM
burlybryan My carbed 1.8 has a bung welded on the drivers sid... Feb 17 2022, 01:12 PM Shivers I do not know the science behind it, may be the al... Feb 17 2022, 01:24 PM ClayPerrine
So many oil leaks.
Even had oil mist out the win... Feb 17 2022, 03:07 PM rhodyguy A Breather Can from Tangerine. No more drawing vap... Feb 17 2022, 01:46 PM NARP74
A Breather Can from Tangerine. No more drawing va... Feb 17 2022, 03:50 PM Spoke Tangerine Racing breather with exhaust going back ... Feb 18 2022, 09:03 PM BK911 Sorta figured out where the oil at cylinder/case i... Feb 23 2022, 08:16 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 17th June 2024 - 11:47 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.