Calling 914 rubber, I need to replace my 43 year old seatbelts. |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
Calling 914 rubber, I need to replace my 43 year old seatbelts. |
pete-stevers |
Jun 3 2022, 12:43 PM
Post
#1
|
saved from fire! Group: Members Posts: 2,642 Joined: 10-October 04 From: Abbotsford,BC, Canada Member No.: 2,914 Region Association: Pacific Northwest |
Hey Mikey!! I hope all is well.. ( I tried to call the 914 rubber line but can't get through... mssg says number not available from our area... Do you have an international number)
My wife and I were driving the highway last week. Three folks did a left hand in front of us... we were going about 55 mph. After the second person turned to close for comfort... I was ready to slam on the brakes... Then a third guy turns left in front of us in a black dodge ram!! I slam on the brakes... thankful I had PMB calipers!! It was close... If I had been going any faster... we would not be chatting about it here. I figure it is time to replace the 47 yr old seatbelts!!! Anyhow. I need a few things Seatbelts for a 1974 and Fiberglass bumper tops ( does the rear have a set up for the license plate light? if it does can you send me the light fixture too) and a couple of other things too, new seat covers and a rear back pad cover. |
Mikey914 |
Jun 3 2022, 06:07 PM
Post
#2
|
The rubber man Group: Members Posts: 12,678 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None |
Well, you should have been able to reach us. Was it the 855-914-GUYS (4897) number?
The seat belts we have not done as of yet. It would be possible, but if other acceptable solutions are available, I'd go that way. As far as cost goes, liability may be what's keeping the costs up. I'd be happy to look into this if there is a need. However on the fiberglass bumper tops we posted up a GB some time back, and are actually to the point we will be able to start producing in quantity. The costs for material have went up some, but shouldn't be too bad. I'll post up the ones I laid up this week a little late this weekend. -Mark |
pete-stevers |
Jun 3 2022, 09:29 PM
Post
#3
|
saved from fire! Group: Members Posts: 2,642 Joined: 10-October 04 From: Abbotsford,BC, Canada Member No.: 2,914 Region Association: Pacific Northwest |
Well, you should have been able to reach us. Was it the 855-914-GUYS (4897) number? The seat belts we have not done as of yet. It would be possible, but if other acceptable solutions are available, I'd go that way. As far as cost goes, liability may be what's keeping the costs up. I'd be happy to look into this if there is a need. However on the fiberglass bumper tops we posted up a GB some time back, and are actually to the point we will be able to start producing in quantity. The costs for material have went up some, but shouldn't be too bad. I'll post up the ones I laid up this week a little late this weekend. -Mark Thanks for the reply! Yes that is the number I dialed, a recording says the number is not available in this area. I am calling from BC. I thought it was kind of weird. I guess I will search for some hardware that is not as rough as mine... and reweb them. |
Mikey914 |
Jun 4 2022, 12:55 AM
Post
#4
|
The rubber man Group: Members Posts: 12,678 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None |
Well, you should have been able to reach us. Was it the 855-914-GUYS (4897) number? The seat belts we have not done as of yet. It would be possible, but if other acceptable solutions are available, I'd go that way. As far as cost goes, liability may be what's keeping the costs up. I'd be happy to look into this if there is a need. However on the fiberglass bumper tops we posted up a GB some time back, and are actually to the point we will be able to start producing in quantity. The costs for material have went up some, but shouldn't be too bad. I'll post up the ones I laid up this week a little late this weekend. -Mark Thanks for the reply! Yes that is the number I dialed, a recording says the number is not available in this area. I am calling from BC. I thought it was kind of weird. I guess I will search for some hardware that is not as rough as mine... and reweb them. Sorry, I missed the BC part. Yes The international toll free cost just to have the line is several hundred a month. just didn't pencil out. The international number is 1-503-352-9434 Mark |
Lo-Fi Version | Time is now: 9th June 2024 - 11:24 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |