 CHT, On a 3.2 |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| NARP74 |
 Jul 17 2022, 12:21 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,445 Joined: 29-July 20 From: Colorado, USA, Earth Member No.: 24,549 Region Association: Rocky Mountains  |
My guess is this is not factory. Where should it be on a 3.2?
 |
   |
 
|
  |
Replies
| Luke M |
Jul 18 2022, 07:24 AM
Post
#2
|
|
Senior Member Group: Members Posts: 1,443 Joined: 8-February 05 From: WNY Member No.: 3,574 Region Association: North East States 
|
QUOTE(NARP74 @ Jul 17 2022, 11:21 AM)  My guess is this is not factory. Where should it be on a 3.2? On a 3.2 the cht sensor screws into the side of the #3 cylinder head. Look at the sheet metal covering that rear section you should see the wire hanging through it. That is if its in a 911 and factory motronic. If not it could be covered up with the engine sheet metal . Either way look at the #3 head. |
|
|
|
| emerygt350 |
Jul 18 2022, 08:35 AM
Post
#3
|
|
Advanced Member Group: Members Posts: 3,407 Joined: 20-July 21 From: Upstate, NY Member No.: 25,740 Region Association: North East States |
QUOTE(Luke M @ Jul 18 2022, 07:24 AM) QUOTE(NARP74 @ Jul 17 2022, 11:21 AM) My guess is this is not factory. Where should it be on a 3.2? On a 3.2 the cht sensor screws into the side of the #3 cylinder head. Look at the sheet metal covering that rear section you should see the wire hanging through it. That is if its in a 911 and factory motronic. If not it could be covered up with the engine sheet metal . Either way look at the #3 head. I think we are looking at an aftermarket cht sender, not a part of the injection system. |
|
|
|
Posts in this topic
NARP74 CHT Jul 17 2022, 12:21 PM
SirAndy My guess is this is not factory
:blink: Jul 17 2022, 12:54 PM Dave_Darling That looks to be a ring thermocouple which would b... Jul 17 2022, 03:42 PM emerygt350 It looks like it is in poor shape too. I wouldnt ... Jul 18 2022, 05:42 AM
Luke M
[quote name='Luke M' post='3015977' date='Jul 18 ... Jul 18 2022, 11:51 AM NARP74 It's in a 914, I am guessing it is just for th... Jul 18 2022, 09:02 AM emerygt350
It's in a 914, I am guessing it is just for t... Jul 18 2022, 09:57 AM emerygt350 Yes, but are you describing the location of the ch... Jul 18 2022, 06:37 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 8th December 2025 - 03:17 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.