 How did you mount dual pole oil pressure sender |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| cgnj |
 Jul 12 2022, 08:28 AM
Post
#1
|
|
Senior Member  Group: Members Posts: 624 Joined: 6-March 03 From: Medford, NJ Member No.: 403 Region Association: None 
 |
Almost ready to wake up the 2270 after dropping the motor to change oil pump & oil pressure relief circuit. How and where did you mount the dual pole sender. I am using a braided steel hose.
Thanks in advance |
   |
 
|
  |
Replies
| ndfrigi |
Dec 21 2022, 10:25 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,933 Joined: 21-August 11 From: Orange County Member No.: 13,474 Region Association: Southern California
|
This one I was planning in doing mine.
  |
 |
|
| nathanxnathan |
Dec 22 2022, 12:34 AM
Post
#3
|
|
Member Group: Members Posts: 285 Joined: 16-February 18 From: Laguna Beach, CA Member No.: 21,899 Region Association: Southern California |
QUOTE(ndfrigi @ Dec 21 2022, 08:25 PM)  This one I was planning in doing mine. I did it that way once. You have to modify the tin. Also the way it looks like that one is done and how I did it, you couldn't remove/replace the sender without removing the tin which is a major job. I used a VW bus ball joint boot for the grommet I recall. I went to a larger Mallory distributor, and I had to relocate it, and regretted having messed up the tin. |
|
|
|
Posts in this topic
cgnj How did you mount dual pole oil pressure sender Jul 12 2022, 08:28 AM
sportlicherFahrer Depending on the length of your braided line you c... Jul 12 2022, 10:20 AM brant It needs to ground I believe at the mount
I once h... Jul 12 2022, 10:24 AM
bdstone914
It needs to ground I believe at the mount
I once ... Jul 12 2022, 10:38 AM dr914@autoatlanta.com go to the auto parts store and get a brass fitting... Jul 12 2022, 11:21 AM brant
go to the auto parts store and get a brass fittin... Jul 12 2022, 04:26 PM ClayPerrine
[quote name='dr914@autoatlanta.com' post='3014785... Dec 22 2022, 03:08 PM VaccaRabite
So I use the same setup George does. But I make ... Sep 27 2023, 05:08 AM nditiz1 metal hose clamp with 2 mounting holes. Mount clo... Jul 12 2022, 11:29 AM NARP74 My car came with this. I was getting flaky readin... Jul 12 2022, 11:50 AM cgnj I think I found the p clamp I used originally.Now ... Jul 12 2022, 03:54 PM nathanxnathan When I ran a dual pole sensor and a larger Mallory... Jul 12 2022, 06:32 PM Brian Fuerbach Ground is no problem with braided line. I sleeved ... Jul 12 2022, 07:22 PM DC_neun_vierzehn
Ground is no problem with braided line. I sleeved... Dec 21 2022, 10:14 PM Porschef
Ground is no problem with braided line. I sleeved... Sep 27 2023, 05:55 AM Jezibel
Ground is no problem with braided line. I sleeved... Feb 24 2024, 09:34 PM ndfrigi
This one I was planning in doing mine.
I did ... Dec 22 2022, 10:01 AM VaccaRabite You will notice a lot of people that started with ... Dec 22 2022, 08:08 AM NARP74
You will notice a lot of people that started with... Dec 22 2022, 10:35 AM friethmiller
You will notice a lot of people that started with... Dec 22 2022, 01:47 PM NARP74
You will notice a lot of people that started wit... Dec 22 2022, 02:59 PM jim_hoyland Looking for a pic of a clean set up Sep 26 2023, 06:51 PM barefoot I used a 1/8 NPT hose, a Tee fitting and a home ma... Sep 27 2023, 01:44 PM 930cabman
I used a 1/8 NPT hose, a Tee fitting and a home m... Sep 27 2023, 03:49 PM emerygt350 Not sure I would call it clean, but I like it. Ex... Sep 27 2023, 04:14 PM FlacaProductions Unfortunately the 42 Draft Design block is no long... Sep 27 2023, 07:33 PM Porschef
Unfortunately the 42 Draft Design block is no lon... Sep 28 2023, 07:58 AM bkrantz I experimented with some different set-ups to use ... Feb 24 2024, 10:01 PM Montreal914 I haven't studied the oil network, but for tho... Feb 25 2024, 11:25 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd June 2024 - 10:25 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.