 Oil Leaks, I am tired of them |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| sdoolin |
 Nov 19 2023, 01:57 PM
Post
#1
|
|
Member  Group: Members Posts: 417 Joined: 1-May 14 From: LouKY Member No.: 17,299 Region Association: None  |
Rebuilt my 2.0 back in 2016. Full "Raby Spec" 2056. Runs very well. It is out of the car right now as I am dealing with a rusty battery tray (separate thread on that). It appears that I have leaks at most/all of the pushrod tube seals, the valve cover seals, and the rear main seal. This is not a surprise to me, I clean the bottom of the engine regularly, and knew this day was coming
Pretty sure I used the Victor Reinz gasket set that came with my engine "kit" from the Type IV Store. I used the cork valve cover seals from the Victor Reinz set. I did not use any RTV anywhere. Hate the stuff. I know I used a rear main seal from GoWesty as someone back then had suggested it is a better part then what is included with the Victor Reinz set. I installed new pushrod tubes and used the O-Rings from the Victor Reinz set. Does anyone really have an oil tight VW Type IV engine? If yes, how does none do that? |
   |
 
|
  |
Replies
| brant |
Dec 4 2023, 03:40 PM
Post
#2
|
|
914 Wizard Group: Members Posts: 11,949 Joined: 30-December 02 From: Colorado Member No.: 47 Region Association: Rocky Mountains 
|
Longer studs for carbs is a standard thing
You will need them |
|
|
|
| sdoolin |
Dec 4 2023, 05:11 PM
Post
#3
|
|
Member Group: Members Posts: 417 Joined: 1-May 14 From: LouKY Member No.: 17,299 Region Association: None |
QUOTE(brant @ Dec 4 2023, 04:40 PM)  Longer studs for carbs is a standard thing You will need them Longer studs it is then. Thank you. Longer is, after all, usually better. Strangely I'm not sure where to source longer studs, so help there would be appreciated. Studs on top of the intake runners could be longer too. I really appreciate all the help from this site! |
|
|
|
| Superhawk996 |
Dec 8 2023, 12:05 PM
Post
#4
|
|
914 Guru Group: Members Posts: 7,028 Joined: 25-August 18 From: Woods of N. Idaho Member No.: 22,428 Region Association: Galt's Gulch
|
QUOTE(sdoolin @ Dec 4 2023, 07:11 PM) QUOTE(brant @ Dec 4 2023, 04:40 PM) Longer studs for carbs is a standard thing You will need them Longer studs it is then. Thank you. Longer is, after all, usually better. Strangely I'm not sure where to source longer studs, so help there would be appreciated. Studs on top of the intake runners could be longer too. I really appreciate all the help from this site! Belmetric is always a good 1st choice https://belmetric.com/studs-and-rods/ Local hardware stores may have them but selection of lengths, thread pitch, and plating is usually very limited. |
 |
|
Posts in this topic
sdoolin Oil Leaks Nov 19 2023, 01:57 PM
Shivers That is the rumor. My last T-4 build didn’t leak... Nov 19 2023, 02:26 PM 914sgofast2 Jake Raby did a video about his frustration in fin... Nov 19 2023, 02:43 PM 930cabman My 2056 build has a couple smallish pushrod tubes ... Nov 19 2023, 05:12 PM Geezer914 I have a 26mm type 1 CB performance oil pump that ... Nov 19 2023, 05:27 PM JeffBowlsby Jake also used to recommend plumbers pipe dope wit... Nov 19 2023, 05:59 PM Literati914 what about the spring loaded tubes, effective or n... Nov 19 2023, 06:10 PM
Shivers
what about the spring loaded tubes, effective or ... Nov 19 2023, 08:14 PM AZBanks
what about the spring loaded tubes, effective or... Nov 19 2023, 10:34 PM burton73
[quote name='Shivers' post='3113735' date='Nov 19... Dec 1 2023, 01:05 PM barefoot For push rod tube seals, I didn't use the gree... Nov 20 2023, 07:57 AM Geezer914 McMaster-Carr chemical resistant viton fluoroelast... Nov 20 2023, 08:04 AM sdoolin
McMaster-Carr chemical resistant viton fluoroelas... Nov 20 2023, 09:10 AM VaccaRabite I always fight with pushrod tube seals. You have ... Nov 20 2023, 08:59 AM sdoolin Thanks for all replies...
I have tried to find th... Nov 20 2023, 09:48 AM Geezer914
Thanks for all replies...
I have tried to find t... Nov 20 2023, 10:44 AM FlacaProductions Nice:
Here's the direct links -
212:
https://... Nov 20 2023, 10:57 AM Geezer914 I had a pair of cast aluminium valve covers and it... Nov 20 2023, 11:36 AM technicalninja Took a bit to find the x shaped viton rings.
this... Nov 20 2023, 12:11 PM 914werke what is the current group-think regarding bolt o... Nov 20 2023, 12:22 PM sdoolin
what is the current group-think regarding bolt ... Nov 20 2023, 12:43 PM sdoolin Thank you geezer for the explicit instructions - v... Nov 20 2023, 12:40 PM technicalninja
Jake Raby did a video about his frustration in fi... Nov 20 2023, 12:48 PM Jack Standz The silicone valve cover gaskets Aircooled.Net use... Nov 20 2023, 12:59 PM sdoolin
The silicone valve cover gaskets Aircooled.Net us... Nov 20 2023, 01:07 PM porschetub
[quote name='Jack Standz' post='3113835' date='No... Dec 2 2023, 03:31 PM sdoolin
[quote name='sdoolin' post='3113836' date='Nov 21... Dec 2 2023, 06:46 PM VaccaRabite Regular valve covers work fine. You don't nee... Nov 20 2023, 01:43 PM ctc911ctc '74 2.0, 28k miles
I tried to tighten the lea... Nov 20 2023, 02:39 PM Geezer914 Second that, Permatex Hi Tac gasket cement on the ... Nov 20 2023, 03:02 PM FlacaProductions The VW logo on the cover goes UPSIDE DOWN when the... Nov 20 2023, 03:37 PM bkrantz The truly leak-free type 4 engine might be a fanta... Nov 20 2023, 08:53 PM brant pushrod seals are an o ring...
they are designed t... Nov 21 2023, 10:50 AM wonkipop
pushrod seals are an o ring...
they are designed ... Nov 22 2023, 01:15 AM sdoolin
pushrod seals are an o ring...
they are designed ... Dec 1 2023, 06:22 PM burton73
pushrod seals are an o ring...
they are designed... Dec 9 2023, 02:41 PM sdoolin Still working on teardown, finding pretty much wha... Nov 30 2023, 07:08 PM Porschef Really despise oil leaks. I suppose owning an air ... Dec 1 2023, 06:36 AM Olympic 914 Wow those tubes look nice. don't think I want... Dec 1 2023, 01:13 PM Jack Standz
Wow those tubes look nice. don't think I wan... Dec 1 2023, 01:31 PM Literati914
[quote name='AZBanks' post='3113747' date='Nov 19... Dec 1 2023, 01:21 PM sdoolin I have ordered new pushrod tubes from TIVStore, ha... Dec 1 2023, 06:19 PM Geezer914 DuPont Moly coat 55 O ring grease! Dec 2 2023, 07:19 AM sdoolin
DuPont Moly coat 55 O ring grease!
I have a... Dec 2 2023, 06:34 PM Front yard mechanic It’s called controled seepage Dec 2 2023, 08:17 AM Literati914
..Just looked closer at the above pushrod tubes. ... Dec 2 2023, 03:45 PM ClayPerrine
..Just looked closer at the above pushrod tubes.... Dec 3 2023, 09:07 AM sdoolin
[quote name='Literati914' post='3115770' date='De... Dec 4 2023, 09:02 AM Dave_Darling
OK and there's multiple options for these on ... Dec 9 2023, 12:55 PM sdoolin Spent all day cleaning. Have a pretty good contact... Dec 2 2023, 06:42 PM Geezer914 Did you install the engine with these covers? I h... Dec 3 2023, 08:54 AM sdoolin Thinking about phenolic spacers, the spacers betwe... Dec 4 2023, 09:24 AM Superhawk996 Or . . . wait for it . . . Longer studs? Dec 4 2023, 09:47 AM sdoolin
Or . . . wait for it . . . Longer studs?
OK, I ... Dec 4 2023, 05:12 PM Geezer914 If running carbs you should run phelonic spacers t... Dec 4 2023, 12:35 PM sdoolin
Belmetric is always a good 1st choice
https://b... Dec 8 2023, 01:42 PM sdoolin More cleaning, inspection, and beginning of re-ass... Dec 8 2023, 12:00 PM rhodyguy You are running the shorter version of intake mani... Dec 8 2023, 12:30 PM sdoolin Attempts to remove existing intake studs have fail... Dec 9 2023, 10:17 AM Superhawk996 Collet style stud install and removal tools specif... Dec 9 2023, 12:20 PM sdoolin Thank you Superhawk996 - which reminds of two diff... Dec 9 2023, 01:43 PM porschetub
Thank you Superhawk996 - which reminds of two dif... Dec 18 2023, 08:37 PM sdoolin More re-assembly today. The special "X-Ring... Dec 18 2023, 06:50 PM Dave_Darling I do not like the bolt-on valve covers for our eng... Dec 20 2023, 03:20 PM rjames
I do not like the bolt-on valve covers for our en... Dec 20 2023, 03:28 PM porschetub
I do not like the bolt-on valve covers for our en... Dec 20 2023, 05:54 PM sdoolin I finally received the CB Performance bolt on valv... Jan 2 2024, 01:48 PM Jack Standz Available for approximately $20 to $25 f... Jan 2 2024, 02:35 PM ericoneal I'm up the road from you in Crestwood and have... Jan 2 2024, 08:18 PM sdoolin
I'm up the road from you in Crestwood and hav... Jan 3 2024, 11:23 AM technicalninja I have one of those flywheel locks.
I've had i... Jan 3 2024, 12:05 PM sdoolin
I have one of those flywheel locks.
I've had ... Jan 3 2024, 01:02 PM Dave_Darling I've used a wrench over one of the clutch moun... Jan 5 2024, 01:56 AM sdoolin Just about ready to go back into the car. I know t... Jan 13 2024, 06:55 PM sdoolin Progress has been slow. Many excuses. But very clo... Mar 10 2024, 11:54 AM technicalninja Nicely done!
Really like your "shop... Mar 10 2024, 01:28 PM sdoolin
Nicely done!
Really like your "shop... Mar 11 2024, 07:33 AM FlacaProductions Green/red is oil pressure sender idiot light. Mar 10 2024, 01:36 PM sdoolin
Green/red is oil pressure sender idiot light.
T... Mar 11 2024, 07:37 AM Dave_Darling [quote name='sdoolin' date='Mar 11 202... Mar 11 2024, 08:40 PM sdoolin
[quote name='sdoolin' date='Mar 11 20... Mar 12 2024, 08:28 AM DRPHIL914 @sdoolin
did anyone every address your question ... Mar 11 2024, 07:23 AM sdoolin
[b]@[url=http://www.914world.com/bbs2/index.php?s... Mar 11 2024, 07:39 AM sdoolin I (finally) have the engine back in the car. I hav... Mar 27 2024, 11:41 AM 930cabman
I (finally) have the engine back in the car. I ha... Mar 27 2024, 12:19 PM Dave_Darling If the difference is about 1 3/4", it would b... Mar 27 2024, 02:03 PM sdoolin
If the difference is about 1 3/4", it would ... Mar 27 2024, 02:16 PM bkrantz Yup, enough play in the exhaust pipe connections t... Mar 27 2024, 09:40 PM sdoolin Loosened everything up, removed the heater ducts a... Mar 29 2024, 07:22 AM GBX0073 Great Picture Looking good ! Mar 29 2024, 08:30 AM technicalninja :agree: :agree: :agree:
Nice and clean!
M... Mar 29 2024, 09:36 AM sdoolin Thanks for the compliments in the cleanliness. But... Mar 30 2024, 07:52 AM technicalninja Post a pic of your leak point please.
Really stra... Mar 30 2024, 08:39 AM technicalninja You're going to need a mirror with all the stu... Mar 30 2024, 08:52 AM sdoolin Pic below. Hard to get a good picture but you can ... Mar 30 2024, 09:27 AM technicalninja I'd first clean all the oil with B12 carb spra... Mar 30 2024, 10:05 AM technicalninja You're running carbs...
My 75 came with a bra... Mar 30 2024, 10:42 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 06:35 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.