 turbo tie rod upgrade, How the heck does this go on? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| TINKERGINEERING |
 Mar 9 2024, 08:13 PM
Post
#1
|
|
Member  Group: Members Posts: 188 Joined: 15-March 20 From: Sierra Madre, CA Member No.: 24,031 Region Association: Southern California  |
I got some turbo tie rods from 914Rubber and I was looking at my steering rack and I was wondering if the previous stock end pieces just need to be screwed off or hammered or what? How do I get these off? Is a special tool needed?
Thanks for your help everybody! Attached thumbnail(s)   
|
   |
 
|
  |
Replies
| Luke M |
Mar 9 2024, 08:32 PM
Post
#2
|
|
Senior Member Group: Members Posts: 1,377 Joined: 8-February 05 From: WNY Member No.: 3,574 Region Association: North East States 
|
The inner tie rod needs to be removed. Get a large wrench to hold the rack and a large prybar/screw driver. Stick prybar or screw driver through inner rod hole and unscrew. Then install new tie rods. Don't forget the thick washers between the inner rod and rack. There is a special wrench to install the new turbo rods but you can also use a thin bike wrench to tighten as well. I do not recall the size but just measure the inner rods square section and buy a wrench from a bike shop that fits.
|
|
|
|
| mepstein |
Mar 9 2024, 08:52 PM
Post
#3
|
|
914-6 GT in waiting Group: Members Posts: 19,315 Joined: 19-September 09 From: Landenberg, PA/Wilmington, DE Member No.: 10,825 Region Association: MidAtlantic Region
|
QUOTE(Luke M @ Mar 9 2024, 09:32 PM)  The inner tie rod needs to be removed. Get a large wrench to hold the rack and a large prybar/screw driver. Stick prybar or screw driver through inner rod hole and unscrew. Then install new tie rods. Don't forget the thick washers between the inner rod and rack. There is a special wrench to install the new turbo rods but you can also use a thin bike wrench to tighten as well. I do not recall the size but just measure the inner rods square section and buy a wrench from a bike shop that fits. I’m pretty sure it’s 32mm. You can buy from a bike shop or Amazon, eBay, etc. The eye bolt on the old tie rod will probably take a bit of muscle to remove. A pipe wrench will also fork for removal. The existing brass washer gets tossed and the thick washer used instead. |
|
|
|
Posts in this topic
TINKERGINEERING turbo tie rod upgrade Mar 9 2024, 08:13 PM
Mikey914 How long til you need it?
We can do a rebuild and ... Mar 9 2024, 09:27 PM Mikey914 How long til you need it?
We can do a rebuild and ... Mar 9 2024, 09:28 PM TINKERGINEERING Ohh glad to hear this is fairly simple. I didn... Mar 9 2024, 10:40 PM Craigers17 Courtesy of Ian:
https://www.youtube.com/watch?v=... Mar 10 2024, 04:58 AM NARP74 Good that you took the rack out. I was doing this... Mar 10 2024, 09:24 AM
slapshot I started doing mine yesterday. I used the method... Mar 10 2024, 06:38 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 10th June 2024 - 03:33 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.