Home  |  Forums  |  914 Info  |  Blogs
 
914World.com - The fastest growing online 914 community!
 
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG. This site is not affiliated with Porsche in any way.
Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners.
 

Welcome Guest ( Log In | Register )

> Clutch & throttle cable questions
DC_neun_vierzehn
post Nov 2 2026, 08:28 AM
Post #1


Senior Member
***

Group: Members
Posts: 696
Joined: 16-November 20
From: Coastal Delaware
Member No.: 24,893
Region Association: MidAtlantic Region



Last night, I think my throttle cable snapped. I believe it snapped somewhere in the tunnel (bc it's still attached at both ends). Bummer bc I just put it on about 6 months ago. I thought I avoided wrapping it around the clutch cable, but I must not have.

Thus, I thought I would replace both cables "while I'm in there" this time (in case the wrapping/rubbing did any damage to the clutch cable). I thought I read in a post recently that if installing both cables, install the throttle cable first, then the clutch calbe, to help avoid the wrapping issue.

Is that the correct order?

I have a bore scope that I will use and will obviously be more careful this time. Any other helpful tips are welcomed.
User is online!Profile CardPM
Go to the top of the page
+Quote Post
 
Reply to this topicStart new topic
Replies
DC_neun_vierzehn
post Nov 5 2026, 09:54 AM
Post #2


Senior Member
***

Group: Members
Posts: 696
Joined: 16-November 20
From: Coastal Delaware
Member No.: 24,893
Region Association: MidAtlantic Region



Do the ball sockets attachments at the end of the throttle cable wear out and lead to occasional pop outs?
User is online!Profile CardPM
Go to the top of the page
+Quote Post
BillC
post Nov 5 2026, 10:53 AM
Post #3


Senior Member
***

Group: Members
Posts: 763
Joined: 24-April 15
From: Silver Spring, MD
Member No.: 18,667
Region Association: MidAtlantic Region



QUOTE(DC_neun_vierzehn @ Nov 5 2026, 10:54 AM) *

Do the ball sockets attachments at the end of the throttle cable wear out and lead to occasional pop outs?

Yes, if you have the kind of socket that has a little circumferential spring inside the opening of the socket cup -- that little circular spring can loose tension and the socket pops off easily.

I prefer the socket version that uses an external retainer spring that slides into two holes in the socket and then clips around the socket shaft. This version generally won't pop off unless there is significant damage to the cup or retainer.

And, if you don't have a retainer spring, either kind, the socket won't stay on at all.

QUOTE(DC_neun_vierzehn @ Nov 4 2026, 02:05 PM) *

So here’s my question: would the wrapping cause the ball socket to pop off (6 months after installing the throttle cable)?

Generally, if your throttle cable is wrapped around the clutch cable, you'll know because your gas pedal will want to move whenever you press or release the clutch.

I think it's more likely that your throttle cable wrapped itself around the clutch cable after the worn socket popped loose.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
DC_neun_vierzehn
post Nov 5 2026, 05:11 PM
Post #4


Senior Member
***

Group: Members
Posts: 696
Joined: 16-November 20
From: Coastal Delaware
Member No.: 24,893
Region Association: MidAtlantic Region



QUOTE(BillC @ Nov 5 2026, 11:53 AM) *

QUOTE(DC_neun_vierzehn @ Nov 5 2026, 10:54 AM) *

Do the ball sockets attachments at the end of the throttle cable wear out and lead to occasional pop outs?

Yes, if you have the kind of socket that has a little circumferential spring inside the opening of the socket cup -- that little circular spring can loose tension and the socket pops off easily.

I prefer the socket version that uses an external retainer spring that slides into two holes in the socket and then clips around the socket shaft. This version generally won't pop off unless there is significant damage to the cup or retainer.

And, if you don't have a retainer spring, either kind, the socket won't stay on at all.

QUOTE(DC_neun_vierzehn @ Nov 4 2026, 02:05 PM) *

So here’s my question: would the wrapping cause the ball socket to pop off (6 months after installing the throttle cable)?

Generally, if your throttle cable is wrapped around the clutch cable, you'll know because your gas pedal will want to move whenever you press or release the clutch.

I think it's more likely that your throttle cable wrapped itself around the clutch cable after the worn socket popped loose.


@BillC

Rut-ro. I didn't see any sort of springs on this ball socket. Can you share pics of either version so I know what's missing?

These pics are not my car, but this is the ball socket I'm talking about. Where are the springs in these pics?

Attached Image
Attached Image
User is online!Profile CardPM
Go to the top of the page
+Quote Post

Posts in this topic


Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



- Lo-Fi Version Time is now: 22nd November 2026 - 05:18 PM
...