 My Frame Repair Project, Warning - Rust Content |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| cdmcse |
 Feb 13 2005, 12:15 AM
Post
#1
|
|
Member  Group: Members Posts: 340 Joined: 17-December 04 From: Georgetown, Ky Member No.: 3,305  |
It seemed like it was going to take forever to make some progress on my rust repair. After spending the entire winter locating parts, grinding, cuting, painting, and learning to weld, I was finally ready to take the plunge....
Also thanks to everyone on the board, I would have never had enough confidence to tackle this without this site!!! BTW: I must be getting addicted to the "914 lifestyle" as I had withdrawal when the site was down. (IMG:http://www.914world.com/bbs2/html/emoticons/happy11.gif) Fist Pic : The Rust Attached image(s) 
|
   |
 
|
  |
Replies
| cdmcse |
Feb 23 2005, 11:42 PM
Post
#2
|
|
Member Group: Members Posts: 340 Joined: 17-December 04 From: Georgetown, Ky Member No.: 3,305 |
After:
Attached image(s) 
|
|
|
|
Posts in this topic
cdmcse My Frame Repair Project Feb 13 2005, 12:15 AM
cdmcse Where the motor mount was. Feb 13 2005, 12:15 AM cdmcse Here we go. Feb 13 2005, 12:17 AM cdmcse The repair piece from a parts car. Feb 13 2005, 12:18 AM cdmcse Clamped. Feb 13 2005, 12:19 AM cdmcse Welded (no making fun) http://www.... Feb 13 2005, 12:20 AM cdmcse The patch for the frame under the engine mount. Feb 13 2005, 12:21 AM cdmcse Patch welded in. Feb 13 2005, 12:22 AM cdmcse This part is next, after a little clean up in the ... Feb 13 2005, 12:23 AM Lou W Looks great, keep the pictures coming. I'm get... Feb 13 2005, 01:30 AM Bleyseng Whats with the electrical cable coming out of the ... Feb 13 2005, 09:41 AM jd74914 looks good http://www.914worl... Feb 13 2005, 10:10 AM cdmcse These cables in the heater tubes are for a front t... Feb 13 2005, 11:25 AM cdmcse Motor Mount is in, I can practially hear the engin... Feb 13 2005, 07:24 PM mharrison You don't need a floor pan to run the engine... Feb 13 2005, 08:13 PM MecGen Thumbs up Dude http://ww... Feb 13 2005, 09:08 PM cdmcse Made some more progress
Before: Feb 23 2005, 11:40 PM cdmcse Outer Firewall back in: Feb 23 2005, 11:43 PM SirAndy did you spray plenty of "metal-ready" inside that ... Feb 23 2005, 11:57 PM cdmcse Yep, I metal readied the hell out of it it. Then I... Feb 24 2005, 12:09 AM Jamie Looks like you're making great progress. We ne... Feb 25 2005, 08:58 PM MecGen Hello
I just spoke with the dist of Por15, for alm... Feb 26 2005, 07:31 AM cdmcse Well, with POR-15 I've noticed that the prep i... Feb 26 2005, 10:42 AM red914 WOW! you have done imipressive work. i see m... Feb 26 2005, 10:47 AM cdmcse Jamie, Another teener, cool. Including yours and ... Feb 26 2005, 11:25 AM cdmcse Ok I made some more progress this weekend. I got t... Feb 27 2005, 11:36 PM cdmcse The new pan... Feb 27 2005, 11:37 PM cdmcse Zee Hole... Feb 27 2005, 11:39 PM cdmcse Zee other hole... Feb 27 2005, 11:39 PM cdmcse Who wants to see down my tunnel? Feb 27 2005, 11:40 PM cdmcse The firewall side of the tunnel... Feb 27 2005, 11:42 PM cdmcse Up the firewall on the driver's side... Feb 27 2005, 11:42 PM cdmcse Broken clutch tube support about half way down the... Feb 27 2005, 11:48 PM cdmcse Broken tube at the firewall... Feb 27 2005, 11:49 PM cdmcse Look, I made some cash while tearing out the floor... Feb 27 2005, 11:51 PM cdmcse Forgot the pic. Feb 27 2005, 11:52 PM cdmcse Why you should always wear your safety gear. This... Feb 27 2005, 11:55 PM Lou W 