914World.com - The largest online 914 community!

My Frame Repair Project, Warning - Rust Content

cdmcse	Feb 13 2005, 12:15 AM Post #1
Member Group: Members Posts: 340 Joined: 17-December 04 From: Georgetown, Ky Member No.: 3,305	It seemed like it was going to take forever to make some progress on my rust repair. After spending the entire winter locating parts, grinding, cuting, painting, and learning to weld, I was finally ready to take the plunge.... Also thanks to everyone on the board, I would have never had enough confidence to tackle this without this site!!! BTW: I must be getting addicted to the "914 lifestyle" as I had withdrawal when the site was down. (IMG:http://www.914world.com/bbs2/html/emoticons/happy11.gif) Fist Pic : The Rust Attached image(s)

Replies

premierauto5150	Apr 21 2005, 11:19 AM Post #2
Member Group: Members Posts: 64 Joined: 28-December 02 Member No.: 33	Chris...I just have to throw in my two cents here....EXCELLENT WORK!!! Like I've said before....its great that you ended up with that car from us and have put your heart and soul in it. I'm jealous now....as if I wasn't the day I drove it you. We can't wait to see it in person and if you need anything just let us know. BTW...after you get this stage of the project done you should consider doing some resto work for others...hint, hint..I have a 73 2.0 that could use your touch!! See ya, Mark www.premier-autosales.com

Posts in this topic

cdmcse My Frame Repair Project Feb 13 2005, 12:15 AM

cdmcse Where the motor mount was. Feb 13 2005, 12:15 AM

cdmcse Here we go. Feb 13 2005, 12:17 AM

cdmcse The repair piece from a parts car. Feb 13 2005, 12:18 AM

cdmcse Clamped. Feb 13 2005, 12:19 AM

cdmcse Welded (no making fun) http://www.... Feb 13 2005, 12:20 AM

cdmcse The patch for the frame under the engine mount. Feb 13 2005, 12:21 AM

cdmcse Patch welded in. Feb 13 2005, 12:22 AM

cdmcse This part is next, after a little clean up in the ... Feb 13 2005, 12:23 AM

Lou W Looks great, keep the pictures coming. I'm get... Feb 13 2005, 01:30 AM

Bleyseng Whats with the electrical cable coming out of the ... Feb 13 2005, 09:41 AM

jd74914 looks good http://www.914worl... Feb 13 2005, 10:10 AM

cdmcse These cables in the heater tubes are for a front t... Feb 13 2005, 11:25 AM

cdmcse Motor Mount is in, I can practially hear the engin... Feb 13 2005, 07:24 PM

mharrison You don't need a floor pan to run the engine... Feb 13 2005, 08:13 PM

MecGen Thumbs up Dude http://ww... Feb 13 2005, 09:08 PM

cdmcse Made some more progress Before: Feb 23 2005, 11:40 PM

cdmcse After: Feb 23 2005, 11:42 PM

cdmcse Outer Firewall back in: Feb 23 2005, 11:43 PM

SirAndy did you spray plenty of "metal-ready" inside that ... Feb 23 2005, 11:57 PM

cdmcse Yep, I metal readied the hell out of it it. Then I... Feb 24 2005, 12:09 AM

Jamie Looks like you're making great progress. We ne... Feb 25 2005, 08:58 PM

MecGen Hello I just spoke with the dist of Por15, for alm... Feb 26 2005, 07:31 AM

cdmcse Well, with POR-15 I've noticed that the prep i... Feb 26 2005, 10:42 AM

red914 WOW! you have done imipressive work. i see m... Feb 26 2005, 10:47 AM

cdmcse Jamie, Another teener, cool. Including yours and ... Feb 26 2005, 11:25 AM

cdmcse Ok I made some more progress this weekend. I got t... Feb 27 2005, 11:36 PM

cdmcse The new pan... Feb 27 2005, 11:37 PM

cdmcse Zee Hole... Feb 27 2005, 11:39 PM

cdmcse Zee other hole... Feb 27 2005, 11:39 PM

cdmcse Who wants to see down my tunnel? Feb 27 2005, 11:40 PM

cdmcse The firewall side of the tunnel... Feb 27 2005, 11:42 PM

cdmcse Up the firewall on the driver's side... Feb 27 2005, 11:42 PM

cdmcse Broken clutch tube support about half way down the... Feb 27 2005, 11:48 PM

cdmcse Broken tube at the firewall... Feb 27 2005, 11:49 PM

cdmcse Look, I made some cash while tearing out the floor... Feb 27 2005, 11:51 PM

cdmcse Forgot the pic. Feb 27 2005, 11:52 PM

cdmcse Why you should always wear your safety gear. This... Feb 27 2005, 11:55 PM

Lou W Mar 1 2005, 12:09 AM
Travis Neff Never too many pics, NEVER! Mar 1 2005, 10:45 AM
cdmcse I welded all the clutch tube breakage, then I adde... Mar 2 2005, 01:54 AM
cdmcse New metal fuel lines secured to the center of the ... Mar 2 2005, 01:55 AM
cdmcse Fuel Tank end Mar 2 2005, 01:56 AM
cdmcse Firewall End. Mar 2 2005, 01:56 AM
cdmcse POR-15 Applied. Is there anything else I should d... Mar 2 2005, 01:58 AM
Jeroen I see light at the end of your tunnel http://www.914world.com/bbs... Mar 2 2005, 06:52 PM
cdmcse mr914, If you are ready to get started on the repa... Mar 2 2005, 08:50 PM
cdmcse OK, more progress...Top coated the POR-15 with som... Mar 4 2005, 01:22 AM
cdmcse http://www.914world.com/bbs2/... Mar 4 2005, 01:23 AM
cdmcse Driver's Side. Mar 4 2005, 01:24 AM
cdmcse Passenger Side. Next I have to finish the passenge... Mar 4 2005, 01:26 AM
Jeroen Impressive job! Go have a Mar 15 2005, 01:19 AM
SpecialK Now that's a view of the center tunnel you don... Mar 15 2005, 03:07 AM
Lou W Looks great http://www.914wo... Mar 15 2005, 11:41 AM
Travis Neff That's love buddy, painting to match on the in... Mar 15 2005, 11:49 AM
Gint Good lookin work! Mar 15 2005, 01:02 PM
cdmcse Well, after the arrival of our new son (March 6th)... Apr 4 2005, 10:52 PM
cdmcse Now back on topic...Passenger side floor re-enforc... Apr 4 2005, 10:54 PM
cdmcse Driver's side floor re-enforcement, this one i... Apr 4 2005, 10:56 PM
cdmcse Right Rear Floor Jackpoint. Apr 4 2005, 10:56 PM
cdmcse Left Rear Jackpoint. Apr 4 2005, 10:57 PM
cdmcse Engine Shelf installed. I finally got all the part... Apr 4 2005, 10:58 PM
cdmcse The interior all grinded and stripped ready to POR... Apr 4 2005, 10:59 PM
cdmcse The Firewall had Zero Rust!!!! Yay... Apr 4 2005, 11:01 PM
michelko Fantastic http://www.914worl... Apr 5 2005, 12:20 AM
Jeroen Excellent work Chris! And congrats on the kid ... Apr 5 2005, 06:00 AM
CptTripps Well done sir....very nice work. I think we need ... Apr 5 2005, 07:07 AM
kafermeister Wow! congrats on the new arrival. You know i... Apr 5 2005, 07:28 AM
Gint Congratulations on the pit crew! Apr 5 2005, 07:38 AM
cdmcse A little farther along... POR-15 Silver Applied Apr 7 2005, 11:08 PM
cdmcse Another... Apr 7 2005, 11:10 PM
Root_Werks Sweet! Another 914 saved from the rust monste... Apr 8 2005, 08:44 AM
maf914 Way to go, Chris! Great looking work. Also... Apr 8 2005, 11:17 AM
cdmcse Well I reached what I feel like is a major milesto... Apr 12 2005, 09:44 PM
cdmcse Another... Apr 12 2005, 09:45 PM
cdmcse Another Apr 12 2005, 09:46 PM
cdmcse Last one. Now just a few more bits on the outside ... Apr 12 2005, 09:47 PM
dakotaewing How did you apply the Por-15 and primer? Gun or br... Apr 12 2005, 09:52 PM
cdmcse http://www.914world.com/b... Apr 13 2005, 09:16 AM
Gint That does look fantastic. Nice work. Apr 13 2005, 10:08 AM
dakotaewing Apr 13 2005, 12:46 PM
cdmcse Apr 14 2005, 12:24 AM
cdmcse ... Apr 14 2005, 12:58 AM
premierauto5150 Chris...I just have to throw in my two cents here.... Apr 21 2005, 11:19 AM
Bleyseng Oh, you mean the one in your avatar pic??? looks l... Apr 21 2005, 12:45 PM
cdmcse

« Next Oldest · 914World Garage · Next Newest »

1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)

0 Members:

Display Mode: Switch to: Standard · Switch to: Linear+ · Outline

Track this topic · Email this topic · Print this topic · Subscribe to this forum

Lo-Fi Version Time is now: 13th September 2025 - 06:54 PM

Invision Power Board v9.1.4 © 2025 IPS, Inc.

...

All rights reserved 914World.com © since 2002

914World.com is the fastest growing online 914 community!
We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ...