 Would you buy this?, 2.0l for $200 canadian |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| redbaron |
 Jun 2 2005, 08:37 AM
Post
#1
|
|
Newbie  Group: Members Posts: 31 Joined: 9-February 05 From: Alberta, Canada Member No.: 3,583  |
Complete 2.0 motor with fan housing, injection, tin, throttle body, coil, distributor etc. etc.
Problem is I don't have much time with it maybe just a leak down test then my decision. What would you do in a few minutes to get an almost informed opinion of the motor. Seller has had it in his garage and after a few years is selling, says it ran well before it came out. it was going into a van and now that project is dead. I will turn it over with a pry bar, then do a leak down, any other ideas. I think $200 canadian dollars is reasonable even if it didn't run, however it means more parts in the yard that I have to explain to the wife. More likely to fly with her if the thing did run. |
   |
 
|
  |
Replies
| Tab914 |
Jun 13 2005, 04:10 PM
Post
#2
|
|
Member Group: Members Posts: 158 Joined: 25-April 04 From: Alexandria, Ontario, Canada Member No.: 1,978 Region Association: Canada |
I wish!! I hear those guys are allowed to drink on the job. They have a beer allocation per day. No, I don't work on a beer line. I work at a ski resort and we sell draft beer here. The beer lines I am talking about are the lines that conect the beer kegs to the beer taps mounted on the bar. They come in with special containers they conect to the lines to run water and a special soap to clean the inside of the lines so that your beer always tastes like it should..........nice and fresh. Getting thirsty now. Talk to ya later.
Cheers, Dominic. (IMG:http://www.914world.com/bbs2/html/emoticons/beerchug.gif) |
|
|
|
Posts in this topic
redbaron Would you buy this? Jun 2 2005, 08:37 AM
! If it's a REAL 2.0...three bolt heads....the h... Jun 2 2005, 08:39 AM redbaron I am looking at it this afternoon, I have my engin... Jun 2 2005, 08:47 AM ! Like I said...if the heads have three bolts where ... Jun 2 2005, 08:56 AM redbaron pic Jun 2 2005, 08:56 AM SLITS Your current injection system will not fit the 3 b... Jun 2 2005, 08:59 AM redbaron $200 candian is about $160usd on a good... Jun 2 2005, 09:49 AM davep Slits is correct, looks like a 1.7, 72 and earlier... Jun 2 2005, 09:57 AM Mark Henry Look for where the intake manifold bolts to the he... Jun 2 2005, 10:07 AM Rhodes71/914 <... Jun 2 2005, 10:30 AM Rhodes71/914 Looking at that pic again the throttle body and ai... Jun 2 2005, 10:33 AM redbaron Well then! It seems my parade may be rained on... Jun 2 2005, 10:34 AM redbaron Parade officially rained out.
4 bolts http://www.914world.com/bbs2/html/e... Jun 13 2005, 11:41 AM
redbaron Heard of Bob, never seen him or the red 914 would ... Jun 13 2005, 06:46 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 2nd June 2024 - 06:03 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.