![]() |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
![]() |
SirAndy |
![]() ![]()
Post
#21
|
Resident German ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Group: Admin Posts: 41,688 Joined: 21-January 03 From: Oakland, Kalifornia Member No.: 179 Region Association: Northern California ![]() |
sooooo, if i were to sell my car (not saying i am going to)(yet) ...
what do you think i could get for it? assuming i get it all cleaned up (paint buffed out again) and get all the goodies installed (rollerbearings, new wheels & tires, new shocks etc.) ... for those of you who don't know the car, i went through a pretty extensive restauration 3 years ago, spend well over $20k on the car so far. you can read about it here, click on the url then on the "Pictures" link ... http://www.sirandy.com/projects/cars/ here is what you would get: - 1970 914-4 - extensive restauration done 3 years ago, all rust taken car off (wasn't much to begin with), replaced rear clip, new seals, new main wire harness - warmed over 2056 (Bad Boyâ„¢), 96mm KB Pistons, dual webers 44 IDF, MSD ign. + dizzy, EuroRace "H" Cam, 9:1 Compression, Tuna Can Oil Sump, 911 rockers, and tons of other goodies. FAST ... - 916 Bodykit, flares and bumpers and spoiler and flared rockers all molded in - SSI Stainless Steel Heat Exchangers, MANTA Performance Muffler (car got HEAT) - sideshifter 901 transmission, Sachs Racing Clutch, light flywheel - fresh paint, Guards Red (911 color, L 80 K) - full rollcage by "TC-Designfab", PCA, POC, PRC, SCCA legal - 911 Style Carbon-Fiber Dash from "Getty", 911 gauge cluster - Street wheels & tires: 8" x 16 Ronal Alloy with 225/50 x 16 front, 9" x 16 Ronal Alloy with 245/45 x 16 rear - Trackwheels & tires: 7x15 "Cookie Cutter" with GoodYear R250 23.0x9x15 Racing Slicks all around - RennShift performance shifter - custom chrome shift knob - center console - high torque starter - GT style engile lid - brand new factory relay board - clutch tube reinforcement - 350mm momo prototypo steering wheel - moveable pass. seat - brand new carpet, new dash and doorpanel vinyl front suspension: - Complete 911 Carrera ('86) front Suspension with Steel Cross-Member - turbo tie rods - bump steer kit - 22mm Tarett Sway-Bar - 19mm Master Brake Cylinder (911) - Vented and cross-drilled 911 Carrera Rotors, Carrera Calipers (freshly rebuild), new brake pads - Boge shocks - 70mm wheel studs with various spacers rear suspension: - new trailing arms (powdercoated yellow) with mueller rollerbearings and new wheel bearings - 914-6 Stub Axles with 911 Hubs - 100mm wheel studs with various spacers - Vented and cross-drilled 911 Carrera Rotors, Carrera Calipers (freshly rebuild), new brake pads - Adjustable Bilstein Shocks with 180lbs progressive Springs - 911 style handbrake setup everything works, all mechanicals, all electrical i think that's it. oh yeah, i also won the "Best Custom" award at the WCC '04 show & shine (IMG:http://www.914world.com/bbs2/html/emoticons/smile.gif) so, what'ch'ya'all think? (IMG:http://www.914world.com/bbs2/html/emoticons/idea.gif) Andy some pics: (IMG:http://www.914world.com/pix/mycar/02.jpg) (IMG:http://www.914world.com/pix/mycar/03.jpg) (IMG:http://www.914world.com/pix/mycar/04.jpg) (IMG:http://www.914world.com/pix/mycar/05.jpg) (IMG:http://www.914world.com/pix/mycar/01.jpg) (IMG:http://www.914world.com/pix/mycar/06.jpg) |
![]() ![]() |
Britain Smith |
![]()
Post
#22
|
||
Nano Member ![]() ![]() ![]() ![]() Group: Members Posts: 2,354 Joined: 27-February 03 From: Hillsboro, OR Member No.: 364 ![]() |
After looking at this reply, I really think he mean't to say $5K-$6K. In my opinion, which is only my opinion, Andy's car is one that has a whole lot of time and money in it and it built to look like what Andy wants it to look like. There are several people who will look at it and not like certain features, the same way that people view my turbo 912 project. There are also some parts of the car that could have been done differently or better, but again I have several parts of my project that have turned out that way. To the right buyer, I think that Andy's car could be worth ~$8.5K. In reality , I believe that it would probably turn into an AX or DE car due to the full cage, suspension goodies, and the hot motor. -Britain |
||
![]() ![]() |
![]() |
Lo-Fi Version | Time is now: 16th June 2024 - 01:00 AM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |