 what clutch tranny piece am i missing?, i know im missing something |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Flat VW |
 Oct 5 2005, 07:23 PM
Post
#1
|
|
Illegal Soapbox Derby Racecar  Group: Members Posts: 1,692 Joined: 13-November 04 From: Phoenix, AZ Member No.: 3,105  |
so i was laying under the car today looking for the clutch connection to the tranny.
found it (IMG:http://www.914world.com/bbs2/html/emoticons/biggrin.gif) i found the pully thing that the clutch cable goes around then i found where the cable should attach to and its not... (IMG:http://www.914world.com/bbs2/html/emoticons/sad.gif) so i can see the rod that comes out of the passenger of the tranny and there is a fork on the end and it has a slot cut in it. i can see that there should be some piece of metal the the clutch cable runs through and then there should be a bolt on the end im guessing. so does anyone know what the missing piece is and where i could pick one up? i have attached a picture of the fork coming out of the tranny one more thing that kinda worries me... when i pull on the lever coming out of the tranny it dosent budge should it? i made sure it was out of gear first, i dont know if that would make any difference so...is that normal? sorry the picture is such low quality its the best i could do. the rod/fork thing im talking about is pretty much in the center of the frame (IMG:http://www.geocities.com/shaggy_nine14/img_1596.jpg) -shaggy (sorry im logged on as my dad) |
   |
 
|
  |
Replies
| shaggy |
Oct 5 2005, 09:25 PM
Post
#2
|
|
mechanic/welder/fabricator Group: Members Posts: 702 Joined: 26-September 05 From: Gilbert, AZ Member No.: 4,869 Region Association: None |
thank for the help
i need my car to be running sooner than when that part could be shipped sorry thanks tho im goin to BAP tomorrow with that part number thanks 736conver so to hold it on should i use m7s or m8s? or should i use those metal self locking ones? would you suggest using lock tight? instead of using the spacer could i just run the nuts up higher on the clutch cable(trunnion?)? or so i have to make myself a spacer? and after i put it back together ho do i adjust it correctly? is there any real formula for how to go about that or is it just trial and error? also i upon removing the carpet around the pedals i notices that my floor board it rather cracked should i take it out and take it to home depot or something and get a new one made or does it not really matter? thanks for the help my car should be up and running again tomorrow hopefully -jim |
|
|
|
Posts in this topic
Flat VW what clutch tranny piece am i missing? Oct 5 2005, 07:23 PM
736conver John,
Cover the shipping and I can send you the p... Oct 5 2005, 07:38 PM SirAndy Oct 5 2005, 07:42 PM dmenche914 The stock piece shown in the other post was made o... Oct 5 2005, 07:46 PM Andyrew one to talk andy.... lol
Mine has yet to fall apa... Oct 5 2005, 07:54 PM 736conver Its a 911 part
Part#91142320503 Oct 5 2005, 07:57 PM hmeeder John;
I'm not drunk enough to focus on your p... Oct 5 2005, 07:59 PM dmenche914 the shift fork contact point with the little winge... Oct 5 2005, 08:03 PM Dave_Darling The 911 part works just fine. The plastic, as men... Oct 5 2005, 08:49 PM bd1308 I used a 2 or 3 M8s and apparently what I believe ... Oct 5 2005, 08:57 PM SirAndy Oct 5 2005, 09:15 PM bd1308 what now?
actually I just remembered that the thr... Oct 5 2005, 09:21 PM bd1308 I wouldn't use locktite.....it would be a huge... Oct 5 2005, 09:39 PM shaggy thank for telling me where to fine one
do you hap... Oct 5 2005, 09:45 PM bd1308 Oct 5 2005, 09:49 PM Dave_Darling M7 nuts; use two of them tightened against each ot... Oct 6 2005, 12:11 AM
Flat VW Shaggy (my boy Jim) fixed it (with your help)... Oct 6 2005, 05:53 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 15th June 2024 - 09:05 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.