 Working on your 914 this Christmas Weekend??, no wife, no relitives, just me :) |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Mueller |
 Dec 20 2005, 11:59 AM
Post
#1
|
|
914 Freak!  Group: Members Posts: 17,146 Joined: 4-January 03 From: Antioch, CA Member No.: 87 Region Association: None 
 |
Well, if Sherryl gets the green light from her doctor on Friday, she'll be leaving for London, England on Sat. with her sister and mom......
so, that leaves me free to goof around for an entire week (IMG:http://www.914world.com/bbs2/html/emoticons/smash.gif) Hopefully I can avoid sitting in front of the TV too much and actually get my lazy butt out to the garage and be productive..... |
   |
 
|
  |
Replies
| r_towle |
Dec 20 2005, 06:51 PM
Post
#2
|
|
Custom Member Group: Members Posts: 24,588 Joined: 9-January 03 From: Taxachusetts Member No.: 124 Region Association: North East States
|
Mike,
Number one:: Spend your time and figure out an off the shelf replacement cv joint/axle combination that requires no machining... Think sand rail and the parts that are already out there... I cant believe that will all the front wheel drive cars out there that there is no simple cv joint replacement off the shelf that will work... Number two:: Figure out an affordable way to build a nice free flow exhaust for the type IV... Im talking pipes and a flowmast, or two cherry bombs... Number Three:: Figure out the audi tranny or the boxster tranny...I want the boxster with the finger paddles...firgure out the issues and make a kit Number Four:: Find me a high CFM 2.5" diameter 12 volt powered fan that can be put inline in the heater tubes in the front trunk Four A:; Find some insulated flexible 2.5" tubing for the heater to replace the paper tubing. Number Five: Design a emailable, printable pattern for under the fender flexible fender liners and a good way to attach them without wrecking the existing paint.. Number six: Find the detailed specs of the car that is rumored to be running 2.4 liter with DJet...the car is in CA somewhere...I want details...what cam especially, and what kind of hp is he making.. That should keep you busy for a few days. Rich |
|
|
|
Posts in this topic
Mueller Working on your 914 this Christmas Weekend?? Dec 20 2005, 11:59 AM
Aaron Cox me too... finish reassembly....and some motorwork.... Dec 20 2005, 12:00 PM TonyAKAVW I need to pull a bunch of parts from the roller, a... Dec 20 2005, 12:05 PM RON S. 4 DAYS OFF THIS WEEKEND,
I'll be fabb... Dec 20 2005, 12:06 PM Lou W I finished stripping the underside of the drivers ... Dec 20 2005, 12:10 PM airsix Mike,
The surface grinder project is progressing b... Dec 20 2005, 12:43 PM Porcharu I get to take the interior out of "das boat" to dr... Dec 20 2005, 01:08 PM SirAndy i'm hoping McMark doesn't have any friends... Dec 20 2005, 01:12 PM Headrage 3 maybe 4 days of no work. Not sure about Friday.... Dec 20 2005, 01:14 PM Mark Henry Maybe you can box up some parts htt... Dec 20 2005, 01:14 PM Tom Perso ... Dec 20 2005, 01:32 PM bd1308 i'm going to be trying to get my d-jet on my c... Dec 20 2005, 01:35 PM tat2dphreak if we know you Mike, you'll end up deciding to... Dec 20 2005, 01:54 PM neo914-6 <... Dec 20 2005, 02:02 PM ChrisNPDrider Next Tues-Thursday are full-on house and 914 proje... Dec 20 2005, 02:31 PM Mueller ... Dec 20 2005, 02:32 PM Dr. Roger <... Dec 20 2005, 02:59 PM jhadler Lets see...
-Finish rocker arm setup and assembly... Dec 20 2005, 03:10 PM Jeroen I'm leaving friday with the wife, daughter, mo... Dec 20 2005, 04:15 PM grasshopper well, I asked for an "all in one cutting system", ... Dec 20 2005, 04:58 PM stock93 Install flares and megasquirt.
John Dec 20 2005, 06:23 PM Trevorg7 Ordered new door panels and speaker ports from mor... Dec 20 2005, 06:25 PM
marks914 Many project beginning this week,
I have 2 weeks ... Dec 20 2005, 06:58 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 6th June 2024 - 07:59 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.