 Stupid Things done while working on a 914., C'mon..... Fess Up! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| ClayPerrine |
 Mar 23 2006, 11:51 AM
Post
#1
|
|
Life's been good to me so far.....  Group: Admin Posts: 16,315 Joined: 11-September 03 From: Hurst, TX. Member No.: 1,143 Region Association: NineFourteenerVille 
 |
There was a request for a thread on stupid stuff done while working on a 914.
I will start...... I had my six up on my lift working on the rear suspension. I remember looking at the clock and it was about 6:50pm. I stood up to do something (I can't remember what now) and the next thing I know, I am sitting on the floor and my head hurts. I touch my head and I am bleeding. (IMG:http://www.914world.com/bbs2/html/emoticons/ohmy.gif) Seems I raised up under one of the rack arms and cracked my head open. I look at the clock and it shows 7:55 PM. (IMG:http://www.914world.com/bbs2/html/emoticons/dry.gif) At that point, I decided to call it a night. When I told Betty about it, she had a fit! (IMG:http://www.914world.com/bbs2/html/emoticons/mad.gif) Her response was "What if you had been holding a cutting torch!!!". Now she insists on checking on me every so often when I am in the garage and it gets quiet for a long time. (IMG:http://www.914world.com/bbs2/html/emoticons/biggrin.gif) Ok... Who's next? |
   |
 
|
  |
Replies
| Joe Ricard |
Mar 23 2006, 04:19 PM
Post
#2
|
|
CUMONIWANNARACEU Group: Members Posts: 6,811 Joined: 5-January 03 From: Gautier, MS Member No.: 92 |
Brand new 18V Milwaukee drill, 300.00
New Cobalt 3/8" drill bit 10.00 needed to drill hole through engine tray to run new gas line etc. lined it up had to put thumb on trigger to drill from underside. Drill bit quickly broke through the sheet metal and screwed it's way to the chuck. Pinned my thumb against the trigger and the car body. new drill had so much torque it smashed my thumb and I couldn't let go. Just kept twisting with me pinned and squirming. Finally reached around and pushed the reverse switch and it let go. THEN IT STARTED TO HURT. Purple thumb and teaching the nieghbor kids some new cuss words Priceless. (IMG:http://www.914world.com/bbs2/html/emoticons/slap.gif) |
 |
|
Posts in this topic
ClayPerrine Stupid Things done while working on a 914. Mar 23 2006, 11:51 AM
olav I was working on my car and my elbow hit my bevera... Mar 23 2006, 11:55 AM effutuo101 LOL! Nothing that dramatic. When I was moving ... Mar 23 2006, 11:58 AM bondo Ok, here's a couple I can think of at the mome... Mar 23 2006, 12:00 PM ! Screwing a tapping metal screw thru the positive b... Mar 23 2006, 12:03 PM jhadler Just getting ready to finish setting up a crank fi... Mar 23 2006, 12:07 PM URY914 I had my dizzy 180 degrees off and shot a flame ab... Mar 23 2006, 12:14 PM Mueller stupid thing: wearing loose fitting sweat pants wh... Mar 23 2006, 12:15 PM SirAndy Mar 23 2006, 12:18 PM URY914 <... Mar 23 2006, 12:18 PM Mueller stood over the carb on a 914/V8 and poured gas int... Mar 23 2006, 12:19 PM URY914 I looked at my car one day and I said to myself, i... Mar 23 2006, 12:27 PM bondo <... Mar 23 2006, 12:28 PM elocke My kids were driving me crazy with croquet mallets... Mar 23 2006, 12:29 PM sk8kat1 I too have a sweat pants story
car on jackstands... Mar 23 2006, 12:29 PM balljoint All the way under the car, lying on my back, car i... Mar 23 2006, 12:29 PM Eric_Shea 
