 Stupid Things done while working on a 914., C'mon..... Fess Up! |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| ClayPerrine |
 Mar 23 2006, 11:51 AM
Post
#1
|
|
Life's been good to me so far.....  Group: Admin Posts: 16,542 Joined: 11-September 03 From: Hurst, TX. Member No.: 1,143 Region Association: NineFourteenerVille 
 |
There was a request for a thread on stupid stuff done while working on a 914.
I will start...... I had my six up on my lift working on the rear suspension. I remember looking at the clock and it was about 6:50pm. I stood up to do something (I can't remember what now) and the next thing I know, I am sitting on the floor and my head hurts. I touch my head and I am bleeding. (IMG:http://www.914world.com/bbs2/html/emoticons/ohmy.gif) Seems I raised up under one of the rack arms and cracked my head open. I look at the clock and it shows 7:55 PM. (IMG:http://www.914world.com/bbs2/html/emoticons/dry.gif) At that point, I decided to call it a night. When I told Betty about it, she had a fit! (IMG:http://www.914world.com/bbs2/html/emoticons/mad.gif) Her response was "What if you had been holding a cutting torch!!!". Now she insists on checking on me every so often when I am in the garage and it gets quiet for a long time. (IMG:http://www.914world.com/bbs2/html/emoticons/biggrin.gif) Ok... Who's next? |
   |
 
|
  |
Replies
| 1bad914 |
Mar 24 2006, 06:01 AM
Post
#2
|
|
Senior Member Group: Members Posts: 618 Joined: 6-May 04 From: Battle Creek, MI Member No.: 2,028 |
Drilling a hole in a piece of sheet metal that I was fabricating for the 914, I'm wearing gloves and being very careful. Then I decide to use the drill bit to elongate the hole...the bit slipped out of the hole and thru the glove and my hand. Went right thru the fleshy part between your thumb and fore finger. The worst part was that it wound up in the leather glove, I had to reverse the drill back out of my hand to get it out. Ouch! Adreniline got me thru it, my wife found me in the garage on my knees looking a little pale!
I wear rubber gloves a lot when I work on the car, smashd my finger while using a hammer, hurt like hell, but I kept on working. About a minute later I looked down at my hand and the glove was full of blood...kewl! Stupid is as stupid does! |
|
|
|
Posts in this topic
ClayPerrine Stupid Things done while working on a 914. Mar 23 2006, 11:51 AM
olav I was working on my car and my elbow hit my bevera... Mar 23 2006, 11:55 AM effutuo101 LOL! Nothing that dramatic. When I was moving ... Mar 23 2006, 11:58 AM bondo Ok, here's a couple I can think of at the mome... Mar 23 2006, 12:00 PM ! Screwing a tapping metal screw thru the positive b... Mar 23 2006, 12:03 PM jhadler Just getting ready to finish setting up a crank fi... Mar 23 2006, 12:07 PM URY914 I had my dizzy 180 degrees off and shot a flame ab... Mar 23 2006, 12:14 PM Mueller stupid thing: wearing loose fitting sweat pants wh... Mar 23 2006, 12:15 PM SirAndy Mar 23 2006, 12:18 PM URY914 <... Mar 23 2006, 12:18 PM Mueller stood over the carb on a 914/V8 and poured gas int... Mar 23 2006, 12:19 PM URY914 I looked at my car one day and I said to myself, i... Mar 23 2006, 12:27 PM bondo <... Mar 23 2006, 12:28 PM elocke My kids were driving me crazy with croquet mallets... Mar 23 2006, 12:29 PM sk8kat1 I too have a sweat pants story
car on jackstands... Mar 23 2006, 12:29 PM balljoint All the way under the car, lying on my back, car i... Mar 23 2006, 12:29 PM Eric_Shea 
