 Tailshifter Linkage Woes, Can't get 1st, 3rd, nor 5th |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Mockmaw |
 Oct 17 2003, 11:37 PM
Post
#1
|
|
Member  Group: Members Posts: 163 Joined: 18-March 03 From: Berkeley/San Diego, CA Member No.: 438  |
Hi all,
New engine is up and running, all very exciting. Problem is: I can't shift into 1st, 3rd, or 5th gear. I fiddled extensively with the shift linkage today.. seems adjusting the shift linkage in the 2nd-3rd plane didn't make a difference. I can shift into reverse, 2nd, and 4th fine.. when I try to shift into 1st, 3rd, or 5th it takes a huge amount of effort and finally pops 'in'.. but it's not actually in gear.. you can feel a bit of grinding if you push the shifter further towards the rear of the car, but it won't go into gear. This is pissing me off.. suggestions? |
   |
 
|
  |
Replies
| rhodyguy |
Oct 18 2003, 10:24 AM
Post
#2
|
|
Chimp Sanctuary NW. Check it out. Group: Members Posts: 22,248 Joined: 2-March 03 From: Orion's Bell. The BELL! Member No.: 378 Region Association: Galt's Gulch |
well put. as the pin bends in the 1,3,5 the whole shebang gets longer. tighten it up and it gets longer. then it breaks just before you have to stop at stop signs on hills while you're in 3rd gear. then you get that sick/sweet smell of clutch.
kevin |
|
|
|
Posts in this topic
Mockmaw Tailshifter Linkage Woes Oct 17 2003, 11:37 PM
URY914 When you put the shift rod back in the coupler (at... Oct 18 2003, 01:44 AM 2teeners I was having some troubles too. It was inside the... Oct 18 2003, 06:03 AM Mockmaw Engine is:
66mm Crank, 96mm P+C's (1911cc)
2.... Oct 18 2003, 09:24 AM rhodyguy get the f.i. fuel line clamps. how did you plumb t... Oct 18 2003, 09:34 AM Mockmaw I just replaced that damn roll pin twice in the la... Oct 18 2003, 09:40 AM rhodyguy as people jam it into gear the stupid thing bends ... Oct 18 2003, 10:00 AM 2teeners if the shift linkage is too long, it won't all... Oct 18 2003, 10:17 AM Bleyseng Nice looking engine! Where does the heads vent... Oct 18 2003, 10:30 AM Mockmaw Okay, it's not the roll pin.. I took the linka... Oct 18 2003, 10:33 AM rhodyguy one down. did you replace the cup in the bottom of... Oct 18 2003, 10:45 AM Mockmaw The cup at the bottom of the shift lever was repla... Oct 18 2003, 11:07 AM Mockmaw Okay, with the car over the pit..
The rear shift ... Oct 18 2003, 11:34 AM McMark Fuel Injec tion hose clamps:
http://www.napaonlin... Oct 18 2003, 12:11 PM Mockmaw Can someone enlighten me on the difference between... Oct 18 2003, 03:00 PM MarkV The non-FI hose clamps have slots that cut into th... Oct 18 2003, 03:03 PM 2teeners That's a nice motor. How does it feel with al... Oct 18 2003, 04:50 PM Red-Beard Mock:
Somehow you've shifted the engine and t... Oct 18 2003, 04:58 PM Red-Beard Better yet: SPend the money and get a side shift t... Oct 18 2003, 04:59 PM
Mockmaw The spending of the money to get the sideshift tra... Oct 18 2003, 05:04 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 3rd July 2025 - 12:30 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.