 OK...I'm goin in!, recommendations on brake install??? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| RS22b |
 Oct 6 2006, 12:25 PM
Post
#1
|
|
Type Broken!  Group: Members Posts: 223 Joined: 8-January 05 From: Vernon, NJ Member No.: 3,425  |
OK, got basically everything lined up and ready to go, but before i start on this thing does anyone have any suggestions or tips on stuff to look out for and proper procedure on stuff?
what i need to know for sure is the procedure for bleeding these things bc they have 2 bleeder valves. THis is the first time in about 25 years that these things are getting replaced. I will be doing the front wheel bearings as well. Any help would be greatly appreciated. THanks, Billy |
   |
 
|
  |
Replies
| So.Cal.914 |
Oct 6 2006, 04:29 PM
Post
#2
|
|
"...And it has a front trunk too." Group: Members Posts: 6,588 Joined: 15-February 04 From: Low Desert, CA./ Hills of N.J. Member No.: 1,658 Region Association: None |
Don't open all the bleeders unless you have speed bleeders and someone to help
you. Open the top bleeder after you have acuired a person to help you, if you don't don't have SBleeders. Pump pedal slow so you don't turn one bubble into a million bubbles, open bleeder. Let person helping you know to let you know when the pedal is to the floor,have him ( or her ) hold the pedal down until you have tightened the bleeder. Continue this procedure until fluid is clear. Rear is the same but you will need to bleed the pro valve first. |
|
|
|
Posts in this topic
RS22b OK...I'm goin in! Oct 6 2006, 12:25 PM
black73 Be more specific on what you plan to do.
Then we ... Oct 6 2006, 03:36 PM Rough_Rider After doing the 944 T calipers i found the best wa... Oct 6 2006, 03:47 PM JPB Get a set of speed bleeders!!! Once i... Oct 6 2006, 04:11 PM Aaron Cox speed bleeders are the shizzle!! Oct 6 2006, 04:13 PM turboman808 Had 2 speed bleeders seize up on me. No thanks. ... Oct 6 2006, 04:15 PM Dave_Darling Ignore the lower bleeders, unless the system has b... Oct 6 2006, 04:24 PM RS22b ok.
Im putting in a new set of discs and wheel be... Oct 6 2006, 04:55 PM
zen motorcycle QUOTE
Eric_Shea QUOTE
rhodyguy that should just about cover it. pick up some pbbl... Oct 7 2006, 01:51 PM So.Cal.914 :agree:
what they said and you can't go wro... Oct 7 2006, 02:10 PM anthony As previously mentioned, learn how the back brakes... Oct 7 2006, 02:14 PM RS22b sounds great eric. thanks for the advice.
I start... Oct 7 2006, 09:20 PM RS22b k. got the new bearings and the front is together ... Oct 8 2006, 12:11 PM So.Cal.914 First use a rubber mallet, should not take anymore... Oct 8 2006, 12:28 PM RS22b sweet. i will see how much they be.
I got the car... Oct 8 2006, 04:53 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 10th June 2024 - 09:00 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.