 Shift Rod Set Screws |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| bd1308 |
 Apr 6 2007, 01:53 AM
Post
#1
|
|
Sir Post-a-lot  Group: Members Posts: 8,020 Joined: 24-January 05 From: Louisville,KY Member No.: 3,501  |
Will regular set screws work until I find suitable replacements?
My set screws are boogered up (stripped out somehow).... I need some set screws....is this a Porsche stocked item? |
   |
 
|
  |
Replies
| Bartlett 914 |
Apr 6 2007, 01:32 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 2,216 Joined: 30-August 05 From: South Elgin IL Member No.: 4,707 Region Association: Upper MidWest |
Sure enough, there is a small plastic pin to lock the thread.
Attached image(s) 
|
|
|
|
| 911quest |
Apr 6 2007, 01:51 PM
Post
#3
|
|
Member Group: Members Posts: 277 Joined: 26-March 06 From: Louisville Ky Member No.: 5,773 Region Association: South East States |
One thing I do on the rear coupler coming out of the body is put a hose clamp around the set screw to keep it from backing out.
|
|
|
|
| Cap'n Krusty |
Apr 6 2007, 09:17 PM
Post
#4
|
|
Cap'n Krusty Group: Members Posts: 10,794 Joined: 24-June 04 From: Santa Maria, CA Member No.: 2,246 Region Association: Central California |
QUOTE(911quest @ Apr 6 2007, 12:51 PM)  One thing I do on the rear coupler coming out of the body is put a hose clamp around the set screw to keep it from backing out. A couple of passes of electrical tape work, too. The Cap'n |
|
|
|
Posts in this topic
bd1308 Shift Rod Set Screws Apr 6 2007, 01:53 AM
SGB Porsche should have 'em, and they aren't j... Apr 6 2007, 07:27 AM Joe Ricard Just spend the money
get the from any of the 914 p... Apr 6 2007, 07:56 AM
911quest I have the rear shift rod with coupler and new bus... Apr 6 2007, 08:22 AM Bartlett 914 Hi Britt.
I plan on making them. I have a couple ... Apr 6 2007, 08:30 AM vsg914
I plan on making them.
Why would you go to the... Apr 6 2007, 09:14 AM Gint
I plan on making them. Why would you go to the tr... Apr 6 2007, 09:19 AM Cap'n Krusty
Hi Britt.
I plan on making them. I have a couple... Apr 6 2007, 11:12 AM Bartlett 914
Hi Britt.
I plan on making them. I have a coupl... Apr 6 2007, 11:28 AM Cap'n Krusty
[quote name='Cap'n Krusty' post='884946' date... Apr 6 2007, 12:16 PM SirAndy
And you don't NEED loctite!
The Cap... Apr 6 2007, 12:20 PM Gint You can make a temp cone screw out of a regular bo... Apr 6 2007, 09:12 AM vsg914 If I was down, I would too. It sounded like Mark i... Apr 6 2007, 09:22 AM Bartlett 914
If I was down, I would too. It sounded like Mark ... Apr 6 2007, 09:40 AM Tobra that is why I bough spares. They are so cheap, wh... Apr 6 2007, 09:48 AM Brando that is why I bough spares. They are so cheap, wh... Apr 6 2007, 07:45 PM brer If it doesn't fit right or is loose it is a sh... Apr 6 2007, 10:17 AM Travis Neff The set screws have a hole in the side (where the ... Apr 6 2007, 10:36 AM Bartlett 914
The set screws have a hole in the side (where the... Apr 6 2007, 11:05 AM sww914 I just smash the hell out of the whole assembly wi... Apr 6 2007, 02:31 PM bd1308 My screw is stripped out....
im goign to try a ov... Apr 6 2007, 08:17 PM 911quest
My screw is stripped out....
im goign to try a o... Apr 6 2007, 09:05 PM Tobra
The set screws have a hole in the side (where the... Apr 7 2007, 08:05 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st June 2024 - 08:04 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.