 Shifting problems please help |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| por73914 |
 Aug 23 2007, 01:44 PM
Post
#1
|
|
I don't know what the hell I am doing...  Group: Members Posts: 349 Joined: 10-April 07 From: Fayetteville, AR Member No.: 7,660  |
I just re-installed my tranny and I cannot get it into 4 and 5th gear. It seems to be a shift rod adjustment but I just can not figure it out! (IMG:style_emoticons/default/headbang.gif)
|
   |
 
|
  |
Replies
| dr914@autoatlanta.com |
Aug 23 2007, 01:50 PM
Post
#2
|
|
914 Guru Group: Members Posts: 8,161 Joined: 3-January 07 From: atlanta georgia Member No.: 7,418 Region Association: None |
QUOTE(por73914 @ Aug 23 2007, 12:44 PM)  I just re-installed my tranny and I cannot get it into 4 and 5th gear. It seems to be a shift rod adjustment but I just can not figure it out! (IMG:style_emoticons/default/headbang.gif) could be a bent rod or broken bushing but to adjust just loosen the bolt in the base and move the shifter over to the right and retighten. |
|
|
|
| por73914 |
Aug 23 2007, 02:12 PM
Post
#3
|
|
I don't know what the hell I am doing... Group: Members Posts: 349 Joined: 10-April 07 From: Fayetteville, AR Member No.: 7,660 |
QUOTE(dr914@autoatlanta.com @ Aug 23 2007, 02:50 PM) QUOTE(por73914 @ Aug 23 2007, 12:44 PM) I just re-installed my tranny and I cannot get it into 4 and 5th gear. It seems to be a shift rod adjustment but I just can not figure it out! (IMG:style_emoticons/default/headbang.gif) could be a bent rod or broken bushing but to adjust just loosen the bolt in the base and move the shifter over to the right and retighten. Thanks George, I moved the shifter to the right and no difference. It seems that it need to go to the left because it is hitting the shift gate and not moving to the right far enough. However upon further inspection I am missing the firewall bushing. Would that cause enough slop to not shift into 4th an 5th? |
|
|
|
| cassidy_bolger |
Aug 23 2007, 03:07 PM
Post
#4
|
|
Member Group: Members Posts: 106 Joined: 17-March 06 From: = Member No.: 5,737 Region Association: None |
I moved the shifter to the right and no difference. It seems that it need to go to the left because it is hitting the shift gate and not moving to the right far enough. However upon further inspection I am missing the firewall bushing. Would that cause enough slop to not shift into 4th an 5th? [/quote] I bet it could. I lost 2nd / 3rd to the left of the detent, and then found that my ball cup bushing was shot. Replaced that and it works perfectly now without even adjusting the shifter. |
|
|
|
| por73914 |
Aug 24 2007, 08:13 AM
Post
#5
|
|
I don't know what the hell I am doing... Group: Members Posts: 349 Joined: 10-April 07 From: Fayetteville, AR Member No.: 7,660 |
I ordered all the bushing this morning, hopefully this will take care of it. Thanks Paul (IMG:style_emoticons/default/driving.gif) |
|
|
|
Posts in this topic
por73914 Shifting problems please help Aug 23 2007, 01:44 PM
tdgray Look over on the Pelican site... there is a write ... Aug 23 2007, 02:16 PM SGB Good move. You will chew up that new trans with s... Aug 24 2007, 08:19 AM
por73914
Good move. You will chew up that new trans with ... Aug 24 2007, 08:22 AM rhodyguy reuse the old cone screws until you are ALL done, ... Aug 24 2007, 11:22 AM por73914
reuse the old cone screws until you are ALL done,... Aug 24 2007, 11:35 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 07:36 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.