 Rocker geo, hoe does this look to you guy's |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| toon1 |
 Oct 28 2007, 09:04 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,849 Joined: 29-October 05 From: tracy,ca Member No.: 5,022  |
so far the liift is good, cam card say's .426, I've got about .428.
Here is a pic. with the vave at half lift. Seems a little off(leaning back) to me. Attached image(s)  
|
   |
 
|
  |
Replies
| Twystd1 |
Oct 31 2007, 01:13 AM
Post
#2
|
|
You don't want to know... really..... Group: Members Posts: 2,515 Joined: 12-September 04 From: Newport Beach, California Member No.: 2,743 |
Uhhhh...
1) Are you setting up your rocker GEO at HALF LIFT...??????? (I don't see that in these last pics) 2) AND are you using an adjustable pushrod to check GEO????? 3) If so (see #2) Is the adjustable pushrod have the same tip as the the other 8 full length pushrods that you will be installing in your engine? 4) Have you read Jakes article on Rocker GEO at his web site? It's a long read. And it might help you figure this out. Clayton |
|
|
|
Posts in this topic
toon1 Rocker geo Oct 28 2007, 09:04 PM
toon1 here are somemore pics of the spacers. notice the ... Oct 28 2007, 09:20 PM toon1 one more Oct 28 2007, 09:20 PM Twystd1 Did you mill your rockers about 60 thou for those ... Oct 28 2007, 11:16 PM Joe Ricard Hey what kinda push rod is that?
Did you make on... Oct 29 2007, 06:08 AM TC.356 Shims beneath the rocker assemblies and longer (ad... Oct 29 2007, 07:34 AM toon1
Hey what kinda push rod is that?
Did you make o... Oct 29 2007, 09:29 AM
George H.
You mentioned oil for the rockers, should it ... Oct 29 2007, 10:33 AM
orange914
I placed the dial indicator back into positio... Nov 3 2007, 12:03 AM craig downs where axactly does the indicator go? wouldnt anyw... Nov 3 2007, 12:48 AM Joe Ricard I oil the rocker shafts with the same oil I do eve... Oct 29 2007, 10:26 AM toon1 there is oil on the rocker shafts, I didnt' oi... Oct 29 2007, 11:24 AM Joe Ricard What really want to know is how much of a clearanc... Oct 29 2007, 11:44 AM toon1 here are some more pics. I added .030 shims under ... Oct 31 2007, 12:23 AM toon1 2 more Oct 31 2007, 12:24 AM toon1
Uhhhh...
1) Are you setting up your rocker GEO a... Oct 31 2007, 11:15 AM toon1 :bump: el bumpo thank's guy's Oct 31 2007, 07:52 PM Twystd1 Do me a favor.....
Throw a straight edge across A... Oct 31 2007, 08:47 PM toon1 with the sraight edge on the tops of the valve ste... Oct 31 2007, 10:20 PM Twystd1 Your gaps are survivable.
If ya want it perfect. ... Nov 1 2007, 12:16 AM craig downs ahhhhh I guess its time to say something and proba... Nov 1 2007, 01:29 AM toon1 thank's guy's, I will give that a try.
... Nov 1 2007, 09:59 AM Joe Ricard That extension thing on the Rocker adjuster is pur... Nov 1 2007, 10:27 AM Joe Ricard Bump for the evening crowd.
Obviously the day su... Nov 1 2007, 03:39 PM HAM Inc The geometry in the last photo looked a lot better... Nov 1 2007, 05:02 PM toon1 thank's for the reply and the good info.
H... Nov 1 2007, 05:43 PM Twystd1 Do not take any more than about 60 thou off the ro... Nov 1 2007, 09:19 PM Twystd1 CRAIG.....
Post up pics of your PS tool / arrange... Nov 1 2007, 09:28 PM toon1 I took another .020 off the rocker. I got your pos... Nov 1 2007, 11:18 PM Twystd1 Since your engine was't machined perfectly to ... Nov 1 2007, 11:45 PM toon1
Since your engine was't machined perfectly to... Nov 2 2007, 12:26 AM craig downs Ok I'll try to get some pics tomorrow.
Hmmm p... Nov 2 2007, 03:08 AM Twystd1 TOON,
A half a MM is way to much to average
Do e... Nov 2 2007, 02:27 PM purple I guess it's kindof a newbie question and all,... Nov 2 2007, 03:33 PM toon1
TOON,
A half a MM is way to much to average
Do ... Nov 2 2007, 08:27 PM Twystd1 Excellent job Keith.....!!!!!... Nov 2 2007, 09:54 PM toon1 DO those #'s look good?
Thank's for the... Nov 2 2007, 10:55 PM Twystd1 Keith,
YOU WILL HAVE TO START OVER ON YOUR GEO WI... Nov 3 2007, 12:02 AM toon1 Thank's Clayton, I'll wait till the cyl... Nov 3 2007, 12:26 AM Twystd1 To the guy that just PMed me about how to INSTALL... Nov 3 2007, 01:00 AM toon1
To the guy that just PMed me about how to INSTAL... Nov 3 2007, 09:45 AM HAM Inc Been out of town for a few days, so I just got up ... Nov 5 2007, 03:10 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st August 2025 - 04:36 AM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.