 Bumper backdate Question on a '75, Re: Location of Holes |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| jim_hoyland |
 Nov 4 2007, 09:16 AM
Post
#1
|
|
Get that VIN ?  Group: Members Posts: 9,696 Joined: 1-May 03 From: Sunset Beach, CA Member No.: 643 Region Association: Southern California 
 |
I had the car up on a lift Friday looking to see if there were spots marked on the sheetmetel where the holes for the early bumpers would be located. I did't have a dogbone handy at the time, but it looked like there are slight indents at the far ends.
I read over both bumper install threads and didn't see a reference to this. Any information will be appreciated-- front and back. Attached image(s) 
|
   |
 
|
  |
Replies
| boxstr |
Nov 4 2007, 01:01 PM
Post
#2
|
|
MEMBER:PACIFIC NORTHWEST REGION Group: Members Posts: 7,522 Joined: 25-December 02 From: OREGON Member No.: 12 Region Association: Pacific Northwest |
Jim Just a couple of thoughts. When you take your bumpers in for rechroming, have them fill the hole in the rear bumper. The screw mount is non existnet on the 75-76 bodies. And if you can get away with it fill the front lic. plate bracket holes.
CCL |
|
|
|
| jim_hoyland |
Nov 4 2007, 06:45 PM
Post
#3
|
|
Get that VIN ? Group: Members Posts: 9,696 Joined: 1-May 03 From: Sunset Beach, CA Member No.: 643 Region Association: Southern California
|
QUOTE(boxstr @ Nov 4 2007, 11:01 AM)  Jim Just a couple of thoughts. When you take your bumpers in for rechroming, have them fill the hole in the rear bumper. The screw mount is non existnet on the 75-76 bodies. And if you can get away with it fill the front lic. plate bracket holes. CCL Is all re-chroming pretty much the same process. Is there anything in particular one should be sure the process includes. Both bumpers are in good condition, one has a small ding, the other is shedding some chrome. Ss picture below. Most of the places I have been to sub out the chrome work to place outside my immediate area. Got the studs...read your thread. Attached image(s) 
|
|
|
|
Posts in this topic
jim_hoyland Bumper backdate Question on a '75 Nov 4 2007, 09:16 AM
rhodyguy these should get you in the ballpark jim. demensio... Nov 4 2007, 10:25 AM jim_hoyland Kevin,
Thanks. I was trying to find out whether t... Nov 4 2007, 10:48 AM boxstr Jim Yes there are indents in the body work. But I ... Nov 4 2007, 12:35 PM euro911 Thats gonna look HOT Jim !!! :D Nov 4 2007, 12:51 PM
jk76.914 I ended up dragging my holes anyway, to get the cl... Nov 4 2007, 03:09 PM computers4kids
I had the car up on a lift Friday looking to see ... Nov 4 2007, 05:49 PM boxstr Jim I think that smaller chrome shops are harder t... Nov 4 2007, 09:48 PM craig downs Problem is a lot of chrome shop are owned by flake... Nov 4 2007, 11:25 PM euro911 Copper, Nickel, Chrome .
Some shops will 'for... Nov 5 2007, 12:30 AM
bbrown You may want to think about adding the "Tow H... Nov 5 2007, 04:20 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 02:17 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.