 944 stubs on 911 hubs, the bearing spacer info you need |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Aaron Cox |
 Mar 16 2007, 08:23 PM
Post
#1
|
|
Professional Tinkerer  Group: Retired Admin Posts: 24,548 Joined: 1-February 03 From: Corona, CA Member No.: 219 Region Association: Southern California  |
ok, so there are two ways to do this im told, you can make a spacer to fill the area on the stub where the dust seal on a 944 used to live, or you can lathe that off, and let the stub sit deeper into the hub-
so here are pics with dimensions...... ill have to go back and write in the dimensions.... cant read the calipers on a few. (shoulda got the digital ones LOL) the materials required. Bearing, early 911 hub, 951 stub, calipers.  Bearing width.  diameter of "dust seal area" and diameter of bearing area on hub.  width of dust seal area  width of bearing area on hub  combined....  bearing diameter if you need it.  |
   |
 
|
  |
Replies
| Krieger |
Nov 29 2007, 07:08 PM
Post
#2
|
|
Advanced Member Group: Members Posts: 4,896 Joined: 24-May 04 From: Santa Rosa CA Member No.: 2,104 Region Association: None 
|
The 944 axles are too long by about 3/4". There are some that are much shorter. I used machined 914/4 axles per a post I found here. Assembled very nicely using new 944 cvs from parts heaven. $84 each. Do a search for 944/911 axles -original date 8/25/06 by Sir Andy. Big Parts needed 915 coarse spline trans flange-parts heaven or easy $75 each, 911 6 bolt 100mm stubs-parts heaven $50 each, early 911 (69-73 I think) stubs. Good machinist. Do not use 944 stubs or you'll have to make/run a spacer. No, I have not installed these in my car yet but the stubs/flanges are identicle dimensionaly where it counts to the 4 parts.
|
|
|
|
Posts in this topic
Aaron Cox 944 stubs on 911 hubs, the bearing spacer info you need Mar 16 2007, 08:23 PM
John I prefer the later hubs, but then you would probab... Mar 16 2007, 09:18 PM Luke M Hey, Aaron
Is that the setup that you have on your... Mar 17 2007, 03:32 PM
ClayPerrine
Hey, Aaron
Is that the setup that you have on you... Mar 17 2007, 03:40 PM
Aaron Cox
Hey, Aaron
Is that the setup that you have on yo... Mar 17 2007, 08:09 PM ClayPerrine
[quote name='ClayPerrine' post='876049' date='Mar... Mar 18 2007, 01:19 AM LarryR
Hey, Aaron
Is that the setup that you have on you... Mar 17 2007, 10:35 PM Luke M Clay,
Which setup do you have on your six?
I'm... Mar 17 2007, 05:30 PM ClayPerrine
Clay,
Which setup do you have on your six?
I... Mar 18 2007, 01:21 AM John Those 944 axles that bolt up to the coarse spline ... Mar 18 2007, 02:07 AM Luke M Clay,
Could you break down the parts/years that yo... Mar 18 2007, 08:10 AM ClayPerrine
Clay,
Could you break down the parts/years that y... Mar 18 2007, 09:02 AM Luke M Thanks, for the info. Clay.
Looks like that may be... Mar 18 2007, 04:32 PM Aaron Cox someone find me those tranny flanges..... Mar 18 2007, 08:42 PM John A no machining/no spacer solution would be:
1. 76... Mar 18 2007, 10:00 PM amallagh John/Clay,
very informative post. Can you confirm... Nov 29 2007, 05:24 PM Elliot Cannon Aaron, are we EVER going to see this car on the ro... Nov 29 2007, 07:11 PM shoguneagle Excellent articles and could not be more timely. ... Nov 29 2007, 11:00 PM amallagh John/Clay,
very informative post. Can you confirm... Nov 30 2007, 02:40 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 6th November 2026 - 09:35 AM |
Invision Power Board
v9.1.4 © 2026 IPS, Inc.