 Clutch tube....... oh fuch |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Gigamight |
 Nov 11 2009, 09:42 PM
Post
#1
|
|
Member  Group: Members Posts: 220 Joined: 8-June 09 From: Near Akron, Ohio Member No.: 10,454 Region Association: Middle East  |
So I was working on the project car today. I must explain before anyone thinks I'm an idiot, there was no engine in the car, and no cables, wiring etc.
So I was working on some real crappy work the PO did on the rear of the firewall, and something seemed to be missing..... finally found it by using a cutoff wheel to remove the top portion of the tunnel. My clutch tube has been jimmyjacked. It was cut about 14 inches before the firewall. there are no welds holding it in. So I need to do some clutch tube work. Any suggestions? Please start at the beginning, after all, remember I am the guy who was working on the car for quite a while before he realized there was no clutch tube exiting the firewall. So, taaaaaalk sloooooooowly. |
   |
 
|
Posts in this topic
Gigamight Clutch tube....... oh fuch Nov 11 2009, 09:42 PM
underthetire From AA
http://www.autoatlanta.com/tech/clutch_tub... Nov 11 2009, 10:06 PM
Gigamight
From AA
http://www.autoatlanta.com/tech/clutch_tu... Nov 12 2009, 09:28 AM r_towle Get a MIG welder and practice how to weld.
I guess... Nov 11 2009, 10:10 PM Gigamight
Get a MIG welder and practice how to weld.
I gues... Nov 12 2009, 09:31 AM Dr Evil Can you find a tube that is slightly larger in dia... Nov 11 2009, 10:21 PM Bartlett 914 Does this picture help? Nov 12 2009, 09:39 AM Gigamight
Does this picture help?
Kinda....
Thanks for ... Nov 12 2009, 09:51 AM Bartlett 914 The tube is welded at 3 points. The rear firewall,... Nov 12 2009, 09:44 AM Bartlett 914 That picture was taken on a car on a rotisserie. T... Nov 12 2009, 10:37 AM Gigamight All right, I am going to bite the bullet and start... Nov 12 2009, 10:50 AM Bartlett 914
All right, I am going to bite the bullet and star... Nov 12 2009, 10:56 AM ThinAir
All right, I am going to bite the bullet and star... Nov 19 2009, 11:32 PM rick 918-S I went to an industrail supply house for truck and... Nov 12 2009, 11:02 AM burton73 You need to put copper in the front of the tube to... Nov 12 2009, 11:16 AM r_towle The tube stops up in front of the shifter about 10... Nov 12 2009, 06:48 PM Greenguy Here is a picture that I took a couple years ago w... Nov 24 2009, 11:18 PM Bartlett 914
Here is a picture that I took a couple years ago ... Nov 25 2009, 08:52 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st June 2024 - 12:54 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.