 Dual carbs for a 2.0, A few questions |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| flipb |
 May 18 2010, 08:08 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 1,728 Joined: 2-September 09 From: Fairfax, VA Member No.: 10,752 Region Association: MidAtlantic Region 
 |
I bought my '74 2.0 with a Weber progressive carb. It's in my plans to switch to dual carbs, probably next fall/winter.
I don't know for certain but I suspect that the Cam is for carbs, not stock. From what I've gathered, 40mm carbs are the right size for a 2.0 motor for street use. Right? I get the feeling that my top choices, in order, are: Dellorto 40mm Weber IDF (Italian-made) 40mm Others? EMPI (modern version of Weber)? Solex? I'm curious to other's input on what to look for and what to avoid. Final question: If I buy a complete setup from classifieds on thesamba, will it fit a 914 2.0? (Intakes and all) Since I've already got the single carb, I presume my low-pressure fuel pump will be appropriate with duals as well... |
   |
 
|
Posts in this topic
flipb Dual carbs for a 2.0 May 18 2010, 08:08 PM
Chris Hamilton I think the best advice would be to find a mechani... May 18 2010, 08:32 PM scrz914 :hijacked: Italian Webers were mentioned. How can... May 18 2010, 09:13 PM jmill I doubt you have a carb cam. A guy who spends the... May 18 2010, 09:14 PM flipb The PO believed there had been an engine rebuild a... May 19 2010, 06:59 AM 9146986 Flip, if you can swing it buy new carbs from a rep... May 19 2010, 07:01 AM
flipb
You also need to check out your distributor and m... May 19 2010, 07:38 AM gothspeed This is all great info! :) May 19 2010, 07:06 AM Root_Werks I have the 40IDF's on my 2.0 and so far, like ... May 19 2010, 08:33 AM gothspeed
I have the 40IDF's on my 2.0 and so far, like... May 19 2010, 09:30 AM Root_Werks
I have the 40IDF's on my 2.0 and so far, lik... May 19 2010, 09:40 AM gothspeed So in your opinion what is the diz for dual webers... May 19 2010, 10:19 AM Root_Werks This one is a decent read:
http://www.thesamba.co... May 19 2010, 09:46 AM Root_Werks Well, everyone has an opinion and I'm sure som... May 19 2010, 10:39 AM 9146986 I heard the 009 was made for industrial engines, b... May 19 2010, 11:10 AM gothspeed Fantastic info guys :). I usually set timming at f... May 19 2010, 11:19 AM Root_Werks
Fantastic info guys :). I usually set timming at ... May 19 2010, 01:26 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 6th June 2024 - 06:17 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.