 Engine lid hinge nut is stripped |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| bandjoey |
 May 24 2010, 06:11 PM
Post
#1
|
|
bandjoey  Group: Members Posts: 4,926 Joined: 26-September 07 From: Bedford Tx Member No.: 8,156 Region Association: Southwest Region  |
What size would you drill and then tap the welded in nut to? Sure would be nice if there was a quick release pin for the engine lid. Thanks.
|
   |
 
|
Posts in this topic
bandjoey Engine lid hinge nut is stripped May 24 2010, 06:11 PM
URY914 Is the the nut that is part of the "L" b... May 24 2010, 06:12 PM URY914 Can't you drill it out and use a longer bolt a... May 24 2010, 06:17 PM
detoxcowboy
Can't you drill it out and use a longer bolt ... May 24 2010, 06:54 PM URY914
Can't you drill it out and use a longer bolt... May 24 2010, 06:59 PM jt914-6 Bill....the stock nut is a 6mm X 1.0 thread. Try r... May 24 2010, 06:20 PM realred914
Bill....the stock nut is a 6mm X 1.0 thread. Try ... May 25 2010, 12:47 PM bandjoey Yes it's on the L bracket. I did the tap, but... May 24 2010, 06:49 PM detoxcowboy
Yes it's on the L bracket. I did the tap, bu... May 24 2010, 06:52 PM tradisrad I tapped mine with an M7 x 1.0 and got the bolt at... May 24 2010, 07:06 PM bandjoey Ah Ha. There is a 7x1 I'll look at that fir... May 24 2010, 08:33 PM tradisrad my tap is a craftsman May 24 2010, 09:40 PM bandjoey
my tap is a craftsman
my banker is my wife
and... May 25 2010, 11:11 AM sean_v8_914 slot the lid tabs. place stud on bracket (car side... May 25 2010, 11:24 AM McMark :agree: 7mm x 1.00 is the way to go.
I've nev... May 25 2010, 11:27 AM ClayPerrine I have a 7mm x 1.0 tap you can borrow. May 25 2010, 12:41 PM kpfoten I just fixed mine last week--took my dremel, secti... May 25 2010, 01:21 PM detoxcowboy 7mm is available but not at your local hardware st... May 25 2010, 01:22 PM realred914
7mm is available but not at your local hardware s... May 25 2010, 02:29 PM bandjoey Will a 7mm tap go through without drilling the hol... May 25 2010, 03:49 PM Bartlett 914
Will a 7mm tap go through without drilling the ho... May 25 2010, 04:07 PM tradisrad my tap has the drill size etched on it. I am prett... May 25 2010, 04:16 PM ClayPerrine Bill...
The Ace hardware on Hwy 26 near my house... May 25 2010, 08:16 PM bandjoey I'm going to Ace tomorrow and pick up a couple... May 25 2010, 09:08 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 8th June 2024 - 12:49 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.