 SS Fuel Line Install Questions |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Spoke |
 Aug 16 2010, 07:34 PM
Post
#1
|
|
Jerry  Group: Members Posts: 6,990 Joined: 29-October 04 From: Allentown, PA Member No.: 3,031 Region Association: None 
 |
I put in SS fuel lines tonight and I've got a few questions.
The engine side of the SS lines looks fine. No issues here.  On the tank side, both fuel lines seem to come out too forward towards the front of the car. The one on the left of the pic is pointing directly into the bulkhead and is touching the bulkhead. Question: Should I try to bend the fuel lines to make some clearance for hoses? I don't want to kink the lines.  The shorter SS fuel lines go through the tin and I don't have the original rubber gaskets. Question: Can these be purchased new or taken off of parts cars or other type of homemade grommet?  I'm assuming the bendable tabs that are shown holding the fuel lines are for the fuel lines, correct? I don't have a FI car to look at.  |
   |
 
|
Posts in this topic
Spoke SS Fuel Line Install Questions Aug 16 2010, 07:34 PM
SLITS Go to HF aand get the cheapo tubing bender ... Put... Aug 16 2010, 07:58 PM tradisrad I had to bend mine at the tank end. I did not go s... Aug 16 2010, 08:02 PM Spoke Thanks. I do have a tube bender tool.
Do I need t... Aug 16 2010, 08:29 PM SLITS I made my own. Ran the tubes through and bent the... Aug 16 2010, 08:33 PM Vacca Rabite If you can get enough purchase on them to bend the... Aug 16 2010, 08:33 PM
Spoke
If you can get enough purchase on them to bend th... Aug 17 2010, 05:16 AM RobW I didn't bend mine on the recent install... ma... Aug 16 2010, 09:21 PM pilothyer Question: Can these be purchased new or taken off ... Aug 16 2010, 11:54 PM Spoke
The rubber grommets you need are the same as the ... Aug 17 2010, 05:15 AM nsr-jamie Are those the Tangerine Racing lines? Looks like y... Aug 17 2010, 04:59 AM SLITS I used the stock grommets. On the front, I pulled... Aug 17 2010, 07:05 AM my928s4 Thanks for this thread, this is one of my next pro... Aug 17 2010, 10:06 AM jim_hoyland What do the instructions say ? I was under the imp... Aug 17 2010, 10:45 AM Spoke If there were instructions, I've lost them. I... Aug 17 2010, 12:26 PM Racer Chris Our fixture allows a range of bend at the front an... Aug 17 2010, 03:18 PM Spoke
Our fixture allows a range of bend at the front a... Aug 19 2010, 12:46 PM jcb29 The bends in the SS tubes just aft of the fire wal... Aug 17 2010, 05:22 PM ejm
You might want to verify the correct location of ... Aug 17 2010, 05:30 PM Lennies914 I picked up a roll of heat shrink (black) at HF an... Aug 17 2010, 05:51 PM Jon Fernandes I just twisted and adjusted them inside the tunnel... Aug 18 2010, 03:22 AM Rotary'14 I put together an install video for SS fuel lines.... Aug 18 2010, 11:28 PM jim_hoyland Nice video Robert ! :) Aug 19 2010, 04:58 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 5th June 2024 - 10:33 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.