 Taco plate leak - Need you help / inside, Did you have the same issue?? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| draganc |
 Dec 9 2010, 02:45 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 725 Joined: 2-November 09 From: central new jersey Member No.: 11,000 Region Association: North East States  |
Hi everybody,
I’m having a leak issue at the taco place and was wondering if you have some advice or experienced similar issue. It appears that the plate leaks only in one area – see picture. The engine has been sitting on my work bench for a few months after rebuild, hence is leaking even at cold temp. - I checked the plate on a mirror and it appears to be flat and the overall condition looks very good – no nicks nor bents or scratches at the sealing surface. - New o-ring and copper washer have been installed. - The M6x10 hex screws have been tighten to spec. - The crank opening measures 84.2mm, the taco plate’s o-ring surface measures 76mm and the o-ring is 4mm thick. It takes only a little bit of force to put the plate in place with mounted o-ring and it appears that plate is already touching the crank-case w/o torquing down the screws. Any ideas or suggestions? Thanks, Dragan   |
   |
 
|
Posts in this topic
draganc Taco plate leak - Need you help / inside Dec 9 2010, 02:45 PM
jaxdream There is a cover plate that goes over top of that ... Dec 9 2010, 05:02 PM yeahmag The cover is not an issue here... I'd get new ... Dec 9 2010, 06:03 PM McMark
I'm guessing you set the 'rim' on th... Dec 9 2010, 06:07 PM draganc Thanks for the tips guys!
I checked the screw... Dec 9 2010, 08:19 PM
draganc Dang it's cold out there...
Here are some mor... Dec 9 2010, 10:17 PM r_towle looks like the o-ring was sitting skewed from that... Dec 9 2010, 10:23 PM draganc
...flatten down where the bolts go...that shiny a... Dec 9 2010, 10:38 PM Racer Chris I checked a taco plate with sender and it measured... Dec 10 2010, 06:28 AM realred914 try another plate, maybe it is bent? you should ... Dec 10 2010, 09:29 AM draganc @ Chris, I guess the 0.9mm would do the trick.
@re... Dec 10 2010, 10:51 AM draganc see below: Dec 15 2010, 09:40 PM draganc Guess what just flew in from Germany?
I guess I fo... Dec 15 2010, 09:41 PM markb Oooo, purty! Dec 15 2010, 10:16 PM Black22 Where did you order that shiny taco from? I want o... Dec 15 2010, 11:23 PM draganc
Where did you order that shiny taco from? I want ... Dec 16 2010, 09:01 AM mtc911 What is the proper torque on the bolts? Oct 3 2019, 08:12 PM bobboinski
What is the proper torque on the bolts?
http:/... Oct 3 2019, 08:48 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 31st October 2024 - 04:46 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.