 Hard to get into gear - when hot, Is this possible??? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| EJP914 |
 May 30 2011, 05:58 PM
Post
#1
|
|
Member  Group: Members Posts: 260 Joined: 14-June 03 From: Monroeville, PA Member No.: 821  |
When the car ('74 1.8) is first run, it shifts ok. After it has been run for awhile and gets hot, I have trouble getting it into any gear especially first where I get a big grinding sound.
I have never replaced the clutch pedal or brake pedal bushings. Is it possible the clutch bushing is swelled up, not allowing the clutch pedal to fully return? It does make a really bad squeak when pushing the pedal in. This might be a really stupid question, but it's all i could think of as the cause. The shifter bushings are fairly new so I don't think it's that. I do have to adjust the free play on the clutch since I just replaced the plastic bushing on the end of the cable. I can't think its a broken clutch cable tube since the shifting is ok when cold. Any suggestion on what may be the cause. Thx in advance for the help. |
   |
 
|
Posts in this topic
EJP914 Hard to get into gear - when hot May 30 2011, 05:58 PM
Elliot Cannon Replacing the pedal bushings isn't too hard on... May 30 2011, 06:15 PM EJP914 Car has been sitting all afternoon. Stone cold. I ... May 30 2011, 06:30 PM
Elliot Cannon
Car has been sitting all afternoon. Stone cold. I... May 30 2011, 07:35 PM jjackson
Car has been sitting all afternoon. Stone cold. ... May 31 2011, 07:04 AM Spoke
Sewickley 1982.JJackson
I grew up in Leetsdale.... Jun 1 2011, 05:07 PM messix is it hard to get into gear when the engine is off... May 30 2011, 06:47 PM Dr Evil Hey Neighbor. I am thinking that this could also b... May 30 2011, 08:51 PM EJP914 Messix: Yes it is hard to get it into gear when t... May 30 2011, 08:56 PM Dr Evil
Messix: Yes it is hard to get it into gear when ... May 30 2011, 09:05 PM messix
Messix: Yes it is hard to get it into gear when... May 30 2011, 09:23 PM URY914 Start by checking that the cone screws are tight. ... May 31 2011, 05:16 AM dirk9141973 :WTF: same problem getting into reverse and 1st ??... Jun 1 2011, 03:50 PM Dr Evil In my 31 pages of notes linked below this is addre... Jun 1 2011, 04:06 PM dirk9141973 :Qarl:
In my 31 pages of notes linked below this ... Jun 1 2011, 05:00 PM charliew From when I was a kid in the 60's if the clutc... Jun 1 2011, 04:18 PM Valy Had a similar problem till I changed the front eng... Jun 1 2011, 06:49 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 8th June 2024 - 10:26 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.