FS 1973 Porsche 914 - San Antonio TX |
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
FS 1973 Porsche 914 - San Antonio TX |
senator914 |
Oct 3 2013, 08:57 PM
Post
#1
|
I'm new here ... Group: Members Posts: 0 Joined: 7-September 13 From: San Antonio Member No.: 16,358 Region Association: None |
1973 Porsche 914 ($7,000 OBO)
2.4L Carb 175 ft-lbs of torque @ 3750 RPM and 135-150 Hp @ 5250 RPM Tangerine Racing Fuel Pump and Fuel Lines for Carburetors Package Rewired with new Hwy 64 kit and new fuse box Chassis stiffening kit Welded new battery tray Installed new stainless steel fuel lines stainless steel brake lines 911 front end 5 lug rear wheel hubs Added re-upholstered seats Center console w/gauges New re-upholstered arm rest Installed new headliner Installed new bright white/blue headlights Rear Porsche Reflector with electronic lock Pillar Gauge Selector Shaft Seal; Transmission Shift Rod Seal; 15x24x7mm Manual Trans Shifter Linkage; Set Screw for Shift Rod Coupling Engine/Motor Mount; Left/Right Manual Trans Shifter Linkage; Shift Coupler Bushing Set (Set of 2); Polygraphite Transmission Overhaul Seal Kit Speedometer Cable Differential Oil Seal; Left/Right Output Seal; 45x68x10mm Wheel Bearing; Rear Left/Right Sealed Bearing;; 42x75x37mm CV Joint Bolt; 8x45mm Hex Porsche 914 rear trunk spring rollers New set of 2 Porsche Aluminium Floor Mat Emblem 914 Lots of extras parts (A/C Unit, Aluminum Foot board and mat, 912 transmission, etc.) New engine: 2.4L Carb 175 ft-lbs of torque @ 3750 RPM and 135-150 Hp @ 5250 RPM Fully bead blasted and repainted sheet metal, accessories, and engine case Cleaned, inspected, and line bored Dual Relief case New AA 104mm Big bore Euro style Flat top Hypertuenic Aluminum P/Cs, ~8.2:1 CR 2.0L 71mm stroke STD Forged Crankshaft cleaned and polished Scat C35 profile cam, cam gear, & Lube a lobe solid lifters Scat 20011 High Rev valve springs Fully Rebuilt and flycut #021 casting 4 stud Porsche Heads New dual 44mm Empi HPMX carburetion system with linkage, intakes, and air cleaners New Mahle STD Rod bearings New Mahle .020”/STD Main bearings New Mahle STD Cam bearings Freshly turned 215mm Flywheel Full Victor Reinz Gasket set All New crankshaft seals New Contitech Alternator belt New Engine tin sheet metal screws New Bosch spark plug wires New Autolite spark plugs New 2.0L 009 electronic Distributor New Cap, Rotor New Compu-fire Super Coil New Bosch oil filter New 1.5 deep oil sump kit Additional oil cooler "Pickup preferred but willing to ship if you pay for the service" |
Lo-Fi Version | Time is now: 1st June 2024 - 12:06 PM |
All rights reserved 914World.com © since 2002 |
914World.com is the fastest growing online 914 community! We have it all, classifieds, events, forums, vendors, parts, autocross, racing, technical articles, events calendar, newsletter, restoration, gallery, archives, history and more for your Porsche 914 ... |