 need to shim throwout clutch fork.what size socket needed |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| rosenfe |
 Jan 26 2014, 02:55 PM
Post
#1
|
|
Senior Member  Group: Members Posts: 557 Joined: 14-October 13 From: northern california Member No.: 16,512 Region Association: None  |
i need to put a shim under the ball that fork sits in.what size socket and socket depth needed to clear the ball ,not much room in there?
|
   |
 
|
Posts in this topic
rosenfe need to shim throwout clutch fork.what size socket needed Jan 26 2014, 02:55 PM
type47 errr, OK, I believe the ball flats (for wrench) ar... Jan 26 2014, 03:18 PM
rosenfe
errr, OK, I believe the ball flats (for wrench) a... Jan 26 2014, 03:27 PM type47
...i dont think there is enough meat for a box en... Jan 26 2014, 03:42 PM tradisrad You will need a 13mm deep socket. I recall having ... Jan 26 2014, 03:37 PM rhodyguy try a 1/4" drive deep socket. Jan 26 2014, 04:23 PM mrbubblehead its a 14mm deep. but you have to grind/thin down t... Jan 26 2014, 05:53 PM Dr Evil 14mm deep that needs the end beveled to fit in the... Jan 26 2014, 06:42 PM rosenfe
14mm deep that needs the end beveled to fit in th... Jan 26 2014, 08:13 PM Cap'n Krusty 14mm or 9/16" deep socket with a very deep co... Jan 26 2014, 09:31 PM Krieger I shimmed mine too. I also used some permatex ult... Jan 26 2014, 11:42 PM JStroud
I shimmed mine too. I also used some permatex ul... Jan 27 2014, 09:19 AM pilothyer
I shimmed mine too. I also used some permatex u... Jan 27 2014, 09:29 AM rosenfe
[quote name='JStroud' post='1989016' date='Jan 27... Jan 27 2014, 11:29 AM jcd914
I believe it is to correct the geometry after a... Jan 27 2014, 11:42 PM r_towle
[quote name='JStroud' post='1989016' date='Jan 27... Jan 27 2014, 01:59 PM Phoenix-MN 14mm sears 3/8" drive socket
Jan 27 2014, 11:32 AM SirAndy 14mm socket that needs to be ground down to fit.
... Jan 27 2014, 12:21 PM rosenfe
14mm socket that needs to be ground down to fit.
... Jan 27 2014, 12:33 PM Cap'n Krusty Snap On "FMS14". It's a 14mm semi-d... Jan 27 2014, 01:00 PM rosenfe
Snap On "FMS14". It's a 14mm semi-... Jan 27 2014, 02:17 PM rosenfe
Snap On "FMS14". It's a 14mm semi... Jan 27 2014, 09:24 PM Cap'n Krusty
Snap On "FMS14". It's a 14mm semi... Jan 27 2014, 11:40 PM Dr Evil Shim? Jeez, it aint that specific. Put another was... Jan 27 2014, 02:12 PM Krieger Yea I use a fat washer to shim. I have a bus flyw... Jan 27 2014, 11:26 PM Amphicar770 Just received a brand new FMS14 socket direct from... Apr 20 2016, 04:28 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 3rd June 2024 - 08:32 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.