 New GB - Heater cables - CORRECT LENGTH - 70-74, YOU NEED THIS!, These will be $24 (+free nipples) for the GB List is over $38 and mine fit |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Mikey914 |
 Jun 15 2016, 10:42 AM
Post
#1
|
|
The rubber man  Group: Members Posts: 12,671 Joined: 27-December 04 From: Hillsboro, OR Member No.: 3,348 Region Association: None 
 |
Again, I've been asked to make correct length heater cables. Apparently the ones on the market are a little too short. These have to be exactly the correct length otherwise they don't reach, and if they are too long the bind up in the flapper arm assembly and will not allow full travel of the flapper, making your heat on not fully on when selected.
These will be nylon coated cables pre-bent for the install at the lever. I've also included 2 free heater cable nipples to seal up the tubes while you are there. So, who's interested? These will be ready in about a week. And who can resist free nipples? Making the 70-74, and the 75-75 version Attached thumbnail(s)  Attached image(s) 
|
   |
 
|
Posts in this topic
Mikey914 New GB - Heater cables - CORRECT LENGTH - 70-74, YOU NEED THIS! Jun 15 2016, 10:42 AM
banananose914 I am in. This is another thing to add to my length... Jun 15 2016, 10:53 AM barefoot I'm in
can't seem to find anyone parting ... Jun 15 2016, 12:20 PM TX914 Interested. But for me they really must fit my 76. Jun 16 2016, 06:14 AM dlee6204 IN. Just broke mine the other day trying to remov... Jun 16 2016, 06:59 AM 76-914 One of the few things I won't be buying from y... Jun 16 2016, 08:06 AM mepstein I need one Jun 16 2016, 08:35 AM bdstone914 There are three different part numbers for the hea... Jun 16 2016, 08:38 AM mepstein The last one I bought did not have the plastic coa... Jun 16 2016, 08:58 AM Mikey914 I have the sample which I will be having fit short... Jun 16 2016, 09:40 AM
76-914
I have the sample which I will be having fit shor... Jun 16 2016, 09:45 AM Mikey914 That's good, because it it is, I have the one ... Jun 16 2016, 10:28 AM bdstone914
That's good, because it it is, I have the one... Jun 16 2016, 12:51 PM 76-914
That's good, because it it is, I have the one... Jun 16 2016, 06:47 PM Mikey914
That's good, because it it is, I have the on... Jun 17 2016, 01:13 AM TX914 Mark,
How did the cable you made for your 75 work ... Aug 17 2016, 09:01 AM Rob-O I'll take one for a '74. Jun 16 2016, 01:29 PM rjames Is the difference in length from early to late car... Jun 16 2016, 11:43 PM Valy One 74 please Jun 17 2016, 12:00 AM Mikey914 1st one (early) sent out for test fitting today. H... Jul 14 2016, 12:30 AM raynekat I'm in... Jul 14 2016, 12:59 AM gcrotvik In for 2 sets! Jul 14 2016, 07:45 AM walterolin One set, 1970-4 Jul 14 2016, 08:21 AM sbsix Mark I need one for a 914-6. Has anyone come forwa... Jul 14 2016, 08:58 AM Mikey914
Mark I need one for a 914-6. Has anyone come forw... Jul 14 2016, 10:21 AM sbsix Sent you a PM. I'll pull out the new one I hav... Jul 14 2016, 03:29 PM sbsix Pictures with measurements from a new cable I have... Jul 15 2016, 12:22 PM Mikey914 Thanks we will be ready to start production this n... Jul 15 2016, 03:21 PM ovation919 I am interested in the 1974 version. Jul 15 2016, 03:54 PM mapguy Need 2 for a '74. Jul 15 2016, 05:47 PM sbsix The picture of the length of the original heater c... Jul 17 2016, 06:37 PM Mikey914 We will be starting to assemble these later this w... Jul 18 2016, 03:12 PM 80cap I don't know how I missed this thread! I ... Aug 17 2016, 10:55 AM Mikey914 I'm sure you could twist it, but will it becom... Aug 17 2016, 03:57 PM TX914
I'm sure you could twist it, but will it beco... Aug 17 2016, 05:02 PM Mikey914
I'm sure you could twist it, but will it bec... Aug 17 2016, 05:27 PM Mikey914 You will need to bump the thread to get the code, ... Aug 17 2016, 04:39 PM mepstein I want an early coated one. Thanks Aug 17 2016, 05:55 PM Mikey914 We will be making the
914/6 version
Early - 70-... Aug 17 2016, 09:53 PM ThinAir :bump:
I'm in for the coated ones.
1973 4 cyl... Aug 17 2016, 11:29 PM Rob-O :bump:
In for '74 with coated wire. Center ... Aug 18 2016, 10:19 AM buck toenges I'll take a coated one for a '71.
Thank... Aug 18 2016, 09:07 PM Mikey914 We will have these listed by Monday. Doing some pr... Aug 20 2016, 09:05 AM Mikey914 Codes sent to all on thread so far.
Made coated a... Aug 20 2016, 11:14 AM rmdinmd :bump: Aug 20 2016, 01:27 PM DEC :bump:
I'm in Aug 21 2016, 01:44 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 23rd May 2024 - 06:13 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.