 Instruction needed for removal of lmpeller, i have to pull the impeller to replace fan shroud- how?? |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| DRPHIL914 |
 Feb 19 2018, 11:37 AM
Post
#1
|
|
Dr. Phil  Group: Members Posts: 5,768 Joined: 9-December 09 From: Bluffton, SC Member No.: 11,106 Region Association: South East States 
 |
do i have to source a puller of some kind?
if so is it a specific kind? thanks Attached thumbnail(s) 
|
   |
 
|
Posts in this topic
Philip W. Instruction needed for removal of lmpeller Feb 19 2018, 11:37 AM
The Cabinetmaker Did you try smacking it (in the middle) with a ham... Feb 19 2018, 12:20 PM Philip W. a ha! got it! no I was not brave enough t... Feb 19 2018, 12:42 PM Larmo63 They can be fussy, but with a little persuasion, t... Feb 19 2018, 12:51 PM Philip W. yes exactly- now, what abouy this?
same thing her... Feb 19 2018, 01:09 PM Philip W. rats! i thought i had a front seal but i have ... Feb 19 2018, 01:17 PM Philip W. is the seal behind this the front crankshaft seal? Feb 19 2018, 01:45 PM cuddyk That black piece behind the hub is the front of th... Feb 19 2018, 02:03 PM Dave_Darling For the fan itself, just grab the edges and rock i... Feb 19 2018, 03:19 PM Perry Kiehl Soak it with what I call "secret sauce" ... Feb 19 2018, 05:44 PM cuddyk dave described the process far more eloquently tha... Feb 19 2018, 06:35 PM Philip W. ok thanks all for the help- that popped off with u... Feb 19 2018, 07:04 PM
ClayPerrine
ok thanks all for the help- that popped off with ... Feb 19 2018, 08:51 PM Jonathan Livesay
ok thanks all for the help- that popped off with... Feb 19 2018, 09:03 PM Philip W. sorry for confusion by "ruin it" I meant... Feb 20 2018, 08:40 AM Philip W. pulled off and cleaned up the motor mounts etc , s... Feb 19 2018, 07:06 PM cuddyk I put a few small screws in the front and used the... Feb 19 2018, 07:19 PM Philip W. there was so much gooey oily junk along thst whole... Feb 19 2018, 08:18 PM Philip W. new seal is in- i winded up using a needle nose vi... Feb 19 2018, 09:44 PM Philip W. just for comparrison here is before i cleaned it u... Feb 19 2018, 09:46 PM Dave_Darling You might want to goop some epoxy over the "f... Feb 19 2018, 09:53 PM Philip W. Dave , what would cause them to pop out? pressure,... Feb 19 2018, 09:55 PM Perry Kiehl Be sure to carefully examine the PRT bores. If th... Feb 19 2018, 10:20 PM Philip W. had not even crossed my mind, doing those plugs- p... Feb 19 2018, 10:28 PM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 3rd June 2024 - 04:44 AM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.