 clutch-cable question |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| bd1308 |
 Jul 1 2005, 08:46 PM
Post
#1
|
|
Sir Post-a-lot  Group: Members Posts: 8,020 Joined: 24-January 05 From: Louisville,KY Member No.: 3,501  |
alright when i did the clutch cable thing, i pulled the slack out of the cable (IE pulled it all the way out till the pedal was all the way up) and tightened it down
question is how much lee-way do i have in the cable from the clutch engaging almost when the pedal is very near the "fully pushed-in" position, to the point when the clutch is slipping whenever driving. |
   |
 
|
Posts in this topic
bd1308 clutch-cable question Jul 1 2005, 08:46 PM
trekkor I like to set my pedal so it must be depressed abo... Jul 1 2005, 08:51 PM john rogers I too set my cable adjustment to release/engage at... Jul 1 2005, 08:54 PM bd1308 how far is the threaded portion behind the nut....... Jul 1 2005, 08:54 PM xsboost90 i had to space my cable. Mine goes about two inche... Jul 1 2005, 09:00 PM bd1308 huh? I thought the pedal went the other way and de... Jul 1 2005, 09:05 PM scotty b Loosen everything up, run the nut back down on the... Jul 1 2005, 09:11 PM bd1308 no the clutch wont dis-engage until the pedal is t... Jul 1 2005, 09:13 PM scotty b When you depress the pedal and reach the end of th... Jul 1 2005, 09:19 PM SGB you should tighten the adjusting nut almost all th... Jul 1 2005, 09:19 PM rhodyguy the pedal end of the cable adj is detailed nicely ... Jul 1 2005, 09:25 PM bd1308 will the cable stretch over a small period of time... Jul 1 2005, 09:43 PM SGB it should not stretch. That has only occured to m... Jul 1 2005, 09:51 PM bd1308 assuming the PP was torqued down, how much cable d... Jul 1 2005, 10:08 PM bd1308 ya think its the roll pin breaking off.....? Jul 1 2005, 10:09 PM xsboost90 cables will stretch, but before they break they st... Jul 1 2005, 10:16 PM bd1308 see i have a bit of a squeak, kinda like bearing s... Jul 1 2005, 10:25 PM xsboost90 you may have that. Could be cable, could be the pi... Jul 1 2005, 10:33 PM Jeff Bowlsby Is your clutch tube in the center tunnel still wel... Jul 1 2005, 10:38 PM bd1308 i dont know how to check. If its the clutch tube g... Jul 2 2005, 08:18 AM Jeff Bowlsby Put an inspection mirror in each of the two access... Jul 2 2005, 08:34 AM
bd1308 okay. thanks. i'll try that. I remember that a... Jul 2 2005, 09:23 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 8th June 2024 - 07:26 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.