 stubborn exhaust manifold gaskets |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| 87m491 |
 Feb 20 2024, 06:55 AM
Post
#1
|
|
Member  Group: Members Posts: 327 Joined: 29-July 12 From: Portland, the original! Member No.: 14,731 Region Association: North East States 
 |
Finally swapping in SS heater boxes I acquired years ago and I can't budge the existing manifold gaskets. I have read and tried a few options, trying to leverage a pick under and edge and walk it out, no luck., the gasket is very tight against the engine. Trying to lever a screwdriver head against and gasket edge and the head to deform the gasket a touch except that my head's fin started to deform before the gasket! Any other tricks before I give up and just try reusing the gaskets that won't seem to come out?
Thx (IMG:http://www.914world.com/bbs2/uploads_offsite/i.imgur.com-14731-1708433712.1.jpg) |
   |
 
|
Posts in this topic
87m491 stubborn exhaust manifold gaskets Feb 20 2024, 06:55 AM
barefoot If they're not damaged in the sealing face, ju... Feb 20 2024, 06:56 AM windforfun What is the gasket material? Can you cut them?
... Feb 20 2024, 11:52 AM
87m491 Theoretically copper but not very malleable from m... Feb 20 2024, 04:46 PM TROJANMAN When all else fails, torch it. :devil: Feb 20 2024, 12:17 PM Shivers I agree, throw some flame on it. Feb 20 2024, 12:22 PM 930cabman It's hard for me to see, but if it's the c... Feb 20 2024, 01:24 PM 87m491
It's hard for me to see, but if it's the ... Feb 20 2024, 04:48 PM GregAmy I snag 'em with a bent pick. $10 for ... Feb 20 2024, 05:35 PM windforfun
I snag 'em with a bent pick. $10 for ... Feb 20 2024, 06:05 PM 930cabman
[quote name='GregAmy' post='3129740' date='Feb 20... Feb 20 2024, 07:08 PM worn
[quote name='GregAmy' post='3129740' date='Feb 2... Feb 27 2024, 08:26 PM DC_neun_vierzehn Sounds like someone may have applied some sealant ... Feb 20 2024, 05:51 PM 87m491
Sounds like someone may have applied some sealant... Feb 25 2024, 02:16 PM Eric_Ciampa I remember deforming one stubborn one. I might hav... Feb 20 2024, 07:57 PM rhodyguy A couple of whacks on the ring with a hammer and s... Feb 25 2024, 02:36 PM windforfun :agree: :agree: :agree:
Cut them with a sharp ... Feb 25 2024, 04:26 PM technicalninja
Sounds like someone may have applied some sealan... Feb 25 2024, 05:11 PM 930cabman Long thin blade slotted screwdriver, a good rap... Feb 27 2024, 02:57 PM 87m491 Deforming of single cylinder gasket on bench I co... Feb 28 2024, 07:23 AM 930cabman
Deforming of single cylinder gasket on bench I c... Feb 28 2024, 10:22 AM rjames
:agree:
Don't run it without replacing it... Feb 27 2024, 08:15 PM 73-914 1/4 in Cold chisel will cut it easy Feb 28 2024, 11:20 AM 87m491
1/4 in Cold chisel will cut it easy
As with so ... Feb 28 2024, 01:35 PM technicalninja I did mine in our 75 upside down.
They were stuck... Feb 28 2024, 02:36 PM 87m491
I did mine in our 75 upside down.
They were stuc... Mar 4 2024, 07:24 AM rhodyguy The cold steel chisel is too blunt. Consider the i... Feb 28 2024, 03:16 PM GregAmy Good on you for keeping at it! Mar 4 2024, 08:10 AM 930cabman Glad you got it out, but I would be careful of cau... Mar 4 2024, 09:21 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th May 2025 - 03:49 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.