 1st flare installed, I was shaking as the steel was cut away |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Joe Ricard |
 Feb 28 2006, 07:36 PM
Post
#1
|
|
CUMONIWANNARACEU  Group: Members Posts: 6,811 Joined: 5-January 03 From: Gautier, MS Member No.: 92  |
OK here is what I did . sanded primed and fit the flare.
marked all the spots for rivets. 3/4" from edge spaced 5 7/8" apart Then used double sticky tape and stuck the fender to the car. marked the layout and position so I could repeat. pulled off flare marked 1 1/2 inches in and made a cut line. Without a single beer I took a deep breath and fired up my Hitachi jig saw with extra fine blade 30 seconds later I had a big ass hole where the fender was. Attached image(s) 
|
   |
 
|
Posts in this topic
Joe Ricard 1st flare installed Feb 28 2006, 07:36 PM
Joe Ricard The hole No turning back now Feb 28 2006, 07:37 PM Joe Ricard Had to trim here and there on the bottom edges of ... Feb 28 2006, 07:38 PM Joe Ricard I just have it hanging on with #6 1/2" hex scre... Feb 28 2006, 07:39 PM Andyrew not nearly the size hole I cut... lol
f/g? Looks ... Feb 28 2006, 07:39 PM Joe Ricard So Paul here ya go to answer the question will the... Feb 28 2006, 07:41 PM Joe Ricard Nuther fatty pic Feb 28 2006, 07:42 PM Joe Ricard and for reference here is a 225/45-15 Hoosier on a... Feb 28 2006, 07:43 PM Joe Ricard nuther Feb 28 2006, 07:44 PM SirAndy did you use the "flared rocker panels" a... Feb 28 2006, 07:52 PM Joe Ricard BONDO???????????? http://ww... Feb 28 2006, 07:55 PM Aaron Cox please weld up your sidemarker hole first.... Feb 28 2006, 08:00 PM Joe Ricard Yea yea yea. it was dark as crap when I cleaned up... Feb 28 2006, 08:04 PM balljoint Just one done? ONE? Whatter you playing around on ... Feb 28 2006, 08:51 PM Joe Ricard Maybe a drawing of "how to" fuck up a... Feb 28 2006, 09:14 PM shadygrady That's looking good. h... Feb 28 2006, 09:21 PM Joe Ricard I have learned that tire numbers have very little ... Feb 28 2006, 09:28 PM J P Stein The only place you may run into a problem is with ... Feb 28 2006, 09:36 PM john rogers That is pretty much just how I did mine. I used so... Feb 28 2006, 09:49 PM Joe Ricard I've been thinking about them rivet washers. G... Feb 28 2006, 10:00 PM J P Stein You didn't ask me, Joe, but mine are wide enuf... Feb 28 2006, 10:16 PM john rogers I use 9x23x15 cantilever slicks on both ends. I ha... Feb 28 2006, 10:59 PM Joe Ricard http://www.914world.com/bbs... Mar 3 2006, 08:26 PM Joe Ricard Close up this is EXACTLY what I wanted Mar 3 2006, 08:27 PM Joe Ricard Under side because Rob asked
nice and tight to the... Mar 3 2006, 08:29 PM J P Stein Hay, good lookin' rivets http:/... Mar 3 2006, 08:29 PM Joe Ricard Figures I got the one rivet that didn't get a ... Mar 3 2006, 08:30 PM Aaron Cox looks cool.
MOAR PICSHORES htt... Mar 3 2006, 08:32 PM Mueller looks good...I changed my mind, can I have my flar... Mar 3 2006, 08:39 PM Joe Ricard Oh yea and special shout out to the old guy JP. ... Mar 3 2006, 08:39 PM Joe Ricard Mar 3 2006, 08:41 PM grasshopper i think that is what i am going to do on my car...... Mar 3 2006, 08:43 PM Aaron Cox ... Mar 3 2006, 09:11 PM URY914 Flares:
916=GT
http://www.914wor... Mar 3 2006, 09:16 PM URY914 Joe,
Do we have to go back and repost all the stuf... Mar 3 2006, 09:18 PM Joe Ricard Mar 3 2006, 09:49 PM Joe Ricard ???????????????? Why do they call the tire a 9.5 w... Mar 3 2006, 09:52 PM Aaron Cox ... Mar 3 2006, 10:20 PM Joe Ricard Rivets????????? No way them too expensive.
How a... Mar 4 2006, 08:44 AM bd1308 there ya go joe! now you're talking. Just ... Mar 4 2006, 08:46 AM Joe Ricard Actually like I said last night maybe if I pinch t... Mar 4 2006, 08:49 AM Joe Ricard nuther Doesn't that just look bad ass?? Mar 4 2006, 08:50 AM Joe Ricard If not it's all going to the dogs. Mar 4 2006, 08:52 AM DNHunt Hey Joe, that duct tape is hundred mile an hour ta... Mar 4 2006, 09:02 AM Joe Ricard Dave, I'm sure there is some humor in your pos... Mar 4 2006, 09:07 AM Bleyseng Joe, its about time you did another Gold Bar run. ... Mar 4 2006, 09:13 AM DNHunt Actually, I meant to comissurate with you. It... Mar 4 2006, 09:22 AM
Joe Ricard Nah. just send a check to Chris he will send you a... Mar 4 2006, 10:34 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 9th June 2024 - 06:57 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.