 Poll: Is your tranny mounted corectly in the rear?, Second attempt |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
| Dr Evil |
 May 30 2008, 03:16 PM
Post
#1
|
|
Send me your transmission!  Group: Members Posts: 23,002 Joined: 21-November 03 From: Loveland, OH 45140 Member No.: 1,372 Region Association: MidAtlantic Region 
 |
Recently I have noticed a lot of trannies that are incorrectly installed concerning the rear mounts. One was soo bad that at a race the rubber in the mounts pulled out leaving the tranny to lie on the ground and breaking the throttle link on the carbs. The other two were on well raced SCCA race cars, but they were not as bad of an error as the dropped tranny one.
Attached is a pic of how it is supposed to go: 40 is the nut that goes on top of 35 35 is a plate that was missing on the dropped tranny racer. This plate keeps the bolt 38 from pulling through the mount 36 36 is held to the frame with 2 grade 8 13mm bolts and nuts, 41, 42, 43 Now comes the parts that always get screwed up..... 37 is mounted below the mount with the CUP PART FACING DOWN. I have been finding these facing up and this will not stop your tranny from sliding off of the bolt. The cup of 37 is meant to go over the ear from the tranny that grabs the bolt. Then 39 is the washer for the bottom of the ear, which is last to go on. Attached image(s) 
|
   |
 
|
Posts in this topic
Dr Evil Poll: Is your tranny mounted corectly in the rear? May 30 2008, 03:16 PM
Dr Evil I reposted to fix the poll....I wish I spell check... May 30 2008, 03:18 PM Eric_Shea Please Do Not Mount the Tranny.
May 30 2008, 03:25 PM
sww914
Please Do Not Mount the Tranny.
Thanks for th... May 30 2008, 07:00 PM davep :barf: :barf: May 30 2008, 03:30 PM Phoenix 914-6GT :rotfl: May 30 2008, 03:30 PM Trevorg7 Guess who did mine?
T May 30 2008, 03:37 PM Krieger914
Guess who did mine?
T
Your what? :barf: May 30 2008, 04:13 PM plymouth37 My tranny is sitting on my garage floor right now ... May 30 2008, 04:35 PM zymurgist I don't know how Babydoll's tranny is moun... May 30 2008, 04:36 PM Borderline Thanks Mike! I should have known you would kn... May 30 2008, 06:59 PM scotty b
Thanks Mike! I should have known you would k... May 31 2008, 05:43 PM SLITS No matter how I mount it I am always correct ........ May 30 2008, 07:19 PM type47 oh no! i read this and had to look at mine. on... May 30 2008, 09:37 PM flat4
oh no! i read this and had to look at mine. o... May 31 2008, 04:52 AM Dr Evil I have some if you need one. I can send it with yo... May 30 2008, 09:48 PM type47
I have some if you need one. I can send it with y... May 31 2008, 06:24 AM Chris Hamilton This thread got me a good :WTF: are you looking at... May 30 2008, 11:27 PM Wilhelm When you mount the tranny don't good manners i... May 31 2008, 03:48 AM plymouth37
When you mount the tranny don't good manners ... May 31 2008, 04:46 AM type47 OK now, i'm not obsessing that i have a part m... May 31 2008, 04:41 PM Dr Evil
OK now, i'm not obsessing that i have a part ... May 31 2008, 10:29 PM SirAndy
I find it disturbing how Eric always has that nas... May 31 2008, 10:31 PM type47
Notches go in towards the tranny. They are for th... Jun 1 2008, 07:40 AM Dr Evil Ya know, I could be wrong about the notches now th... Jun 1 2008, 10:52 AM roadster fan I thought the notched cup washers were for the rub... Jun 1 2008, 02:06 PM type47
I thought the notched cup washers were for the ru... Jun 1 2008, 02:44 PM Dr Evil
I thought the notched cup washers were for the r... Jun 1 2008, 04:02 PM Jax914 yeah...the notched ones are for the early engine m... Jun 2 2008, 06:29 PM chris914 These are off my car. Are they stock?
Jun 22 2008, 08:52 PM Dr Evil yup Jun 22 2008, 09:05 PM FourBlades The last thing I expected this morning from the fo... Jun 23 2008, 08:06 AM watsonrx13 Dr., is this mounted correctly?
http://www.tampab... Jun 25 2008, 06:10 AM Dr Evil Yup :) :thumbsup: Jun 25 2008, 11:57 AM watsonrx13
Yup :) :thumbsup:
Great, now I can answer this ... Jun 25 2008, 06:45 PM r_towle Two extra heavy duty coat hangers here.
I sprung f... Jun 25 2008, 06:51 PM zx-niner Now I'm confused. Rob's photo shows the b... Jun 25 2008, 07:30 PM Dr Evil
Now I'm confused. Rob's photo shows the ... Jun 25 2008, 09:53 PM Phoenix 914-6GT I think it's better having the bolt down. You ... Jun 25 2008, 10:26 PM scotty914
So if you have the nut up it really will be a bi... Jun 26 2008, 02:35 AM ArtechnikA Mine were installed by the factory, so I'd hav... Nov 7 2008, 06:44 PM J P Stein Save some weight with WEVO.....my nuts are down...... Nov 8 2008, 11:21 AM RJMII So, what's better... nuts up or nuts down? I p... Nov 8 2008, 05:08 PM J P Stein "Best shop practice"......an oldie but g... Nov 9 2008, 10:21 AM  |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 1st June 2024 - 10:49 PM |
Invision Power Board
v9.1.4 © 2024 IPS, Inc.